Sailboat 16 Foot/s Price Boats for sale
1-7 of 7
Sort By
45 Foot Morgan Design S&J Sailboat
$13,000
Galveston, Texas
Category -
Length 45.0
Posted Over 1 Month
1977 45 foot Morgan Starratt and Jenks Sailboat (Coast Guard Documented) Hull material: fiberglassHull shape: full keel (lead encapsulated - 12,000 lb. ballast)Length: 45 ft. 9 in.Beam: 11 ft.Draft: 6 ft. 1 in. Engine: Volvo Penta D2 55 F (new engine and new gearbox installed 2011)Current engine hours: 27Shaft: 1.25 in. Diameter / Aqua Met 19 material (new 2011)Shaft Seal: PSS drip less shaft seal with carbon flange and stainless steel collar (new 2011)Prop: Two blade fixed 18 in. Diameter X 13 in. PitchExhaust: Inline water lift muffler and 2.5 in. Corrugated exhaust hose with exhaust Groco valve for heavy following seas (all new 2011)New throttle cable 2011Water strainer: Groco top of the line bronze strainer (new 2011)Raw water hoses: all new 2011 Standing Rigging: 1x19 stainless steel 316 material; uppers 3/8 in., lowers 5/16 in. Two back stays(could setup as yawl), one forestay, two upper side stays, four lower side stays. Hayn Hi-Mod compression eyes (top and bottoms) & huge turnbuckles, toggles. (All New 2011, except turnbuckles and toggles). Bottom paint: 7 coats Pettit Vivid bottom paint( multi colors for different layers) 2011Bottom primer: 3 coats Pettit Hi-build epoxy primer & 2 coats west epoxy below the primer. 2011 Starting battery: AGM Sears Die Hard Platinum deep cycle / starting (2011 new)House battery: AGM 8D Mastervolt (2011 new)Battery switch / isolator installedSolar Panel: 40 wattShore power charger: 10 amp each x 2 banks (AGM, gel, or conventional)LED spreader lights (new 2011), AC shore power outlets inside cabin (4 installed) Communications: VHF, RG213 ancor cable (new 2011), new Antennae whip 2011 Steering: Edson, rudder pinned at bottom of keel with bronze shoe. Stainless steel rudder shaft. Diesel Tank: Needs new, location for at least 50 gallons. Fresh water tanks: 1 plastic at least 20 gallons, plus Vetus water bladder.Holding tank: 1 with plumbing ready for new head (head currently not installed, plumbing is installed though) Berthing: 1 quarter berth, one cabin, one v berth area, but storage area for now, one couch location capable of adult sleeping, one couch area capable of child sleeping.Cushions: cockpit cushions provided in good shape, new interior cushions needed. Galley area: Nice double deep stainless steel sink, Formica counter tops, stove in good condition with stainless steel fuel tank and pressure gauge. Boat is sold as is and where is, descriptions given for reference only. It is buyers duty to make thorough investigation prior to making offer or accepting buy it now price. Non-refundable deposit is required upon accepting buy it now price or placing offer that is accepted by seller. Buyer is responsible for storage, and delivery upon purchase. No warranties apply or given from seller. Buyer assumes all responsibility of ownership fully! For viewing of vessel or questions prior to close of listing, please notify seller via email [email protected] or thru eBay platform.
1982 S2 8.5A 28 foot Sailboat with Inboard Yanmar Diesel - In Racine Wisconsin
$2,750
Racine, Wisconsin
**** PLEASE NOTE: Because of the relatively low BUY IT NOW price, payment will be due within 24 hours via paypal. I will send you a paypal invoice after a successful "BUY IT NOW" or an accepted offer. Please only buy or offer if you have positive feedback. Your buy it now or offer constitutes a binding agreement to purchase so please ask questions BEFORE clicking "BUY IT NOW" or making an offer. After receiving your payment I will overnight you the title or meet you in person depending on timing and my availability.**** Very Nice S2 8.5A (28ft) for sale in Racine Wisconsin. I'm expecting a second child soon and really don't want to sell this excellent great lakes cruiser. Clean and clear Wisconsin title.Tiller steering. (always my preference)Inboard Yanmar diesel is extremely clean and fuel efficient. Recent full Yanmar service checkout since boat was last launched.Furling headsail in good shape. Newer mainsail in excellent shape.New Raymarine autopilot professionally installed. Shore power and long power cable. Halyards in good shape.New marine head and holding tank (never used). Chainplates recently professionally rebedded by boatyard. Interior in excellent shape.Solid fiberglass hull. All tabbed in joinery in excellent shape. Cored deck with NO soft spots. Very large cockpit.Includes steel cradle as well. I looked at everything in this size and price range in the lower half of lake Michigan for two years and this is the nicest boat I could find by leaps and bounds. Solid turnkey value. Launch is all ready paid for with the boat yard. You can be in the water tomorrow. No better deal can be found on solid and ready to sail Great Lakes cruiser with a clean inboard diesel - it is just time for me to move it along. Currently out of the water at Racine Riverside Marina in Racine, WI. Summer storage is paid through the end of this month and a launch is included in the purchase. If you chose not to launch until next season the storage rates at the Marina for winter are extremely reasonable and the pre-paid launch will still be yours come next summer. Here is a Review from "Practical Sailor" S2 8.5 MeterThe 8.5 is good for cruising the coasts in comfort and style--as long as you like the modern look.When Leon Slikkers founded S2 Yachts in 1973, much of the attention to detail that had previously characterized Slickcraft powerboats—Slikkers’ earlier boatbuilding venture— traveled with him to the new boatbuilding company. In the 13 years S2 sailboats were in production (S2 still makes powerboats), the company produced a variety of modern cruising designs from the board of Arthur Edmunds, all characterized by longish fin keels, freestanding spade rudders, straight sheerlines, and a staggering variety of draft options and cockpit locations. In the early ’80s, S2 reached more for the performance market with the Grand Slam series of small boats, and the 10.3 “offshore racer-cruiser.” These higher performance boats were designed by Scott Graham and Eric Schlageter, well known for their MORC and smaller IOR designs.The S2 8.5 is a 28-footer cast in the company’s traditional mold. Her hull dimensions, sail area, displacement, and general design characteristics put her square in the middle of the modern 28-footers such as the Tanzer 8.5, Newport 28, O’Day 28, and the Pearson 28.The boat’s styling is conventionally modern. She has a fairly straight sheer, fairly high freeboard, and low, raked cabin trunk with dark tinted flush ports. Production of the 8.5 ran from 1981 to 1983. The boat was replaced by the similar S2 8.6, which continued until S2 stopped making sailboats in 1986.ConstructionThe hull of the S2 8.5 is a solid hand layup. Glasswork is excellent, and is noted by owners as one of the main considerations in buying the boat. Gelcoat quality is excellent.Slight roving printthrough is evident, but it is not objectionable. Minor hard spots are visible in the topsides, probably caused by the attachment of interior furniture and bulkheads.The deck molding is cored with end grain balsa, giving a solid feel underfoot as well as providing reasonable insulating properties.S2’s hull-to-deck joint is the basic type that we would like to see adopted throughout the industry. The hull molding has an inward-turning flange, onto which the deck molding is dropped. The joint is bedded in flexible sealant, and through bolted on six inch intervals by bolts passing through the full length slotted aluminum toerail. The joint is also through bolted across the stem.All deck hardware is properly through bolted, although pulpits, cleats, and winches merely use nuts and washers on the underside of the deck, rather than the aluminum or stainless steel backing plates we prefer.Another feature of the hull-to-deck joint is a heavy, semi-rigid vinyl rubrail at the sheerline, quite aptly termed a “crash rubrail” by S2. This will go a long way toward absorbing the shock of the inevitable encounters with docks and the other hard objects that seem to be attracted to the topsides of the typical sailboat. Although this rail is black when the boat is new, it had dulled to a chalky gray on older S2’s we examined.The builder advertises “bronze seacocks on all through hull fittings.” These are not traditional tapered plug seacocks, but are ball valves mounted directly to through hull fittings. A proper seacock—whether it uses a ball valve or a tapered plug—has a heavy flange to allow through bolting to the hull. This is an important safety feature. Should a valve seize, it may become necessary to apply a great deal of leverage to the handle in order to open or close the valve. The deeply threaded through hull stem can easily break under these conditions, and more than one boat has been lost in this manner.We also suggest that seacocks be installed on the cockpit drain scuppers and the bilge pump outlet, both of which may be under water while the boat is sailing. Light air performance would benefit by the fairing in of the through hull fittings, particularly the head intake and discharge, both of which are far enough forward to have a significant effect on water flow past the hull.Ballast is a 3,000 pound lead casting, epoxied inside a hollow keel shell. We prefer an external lead casting bolted to the hull for its shock-absorbing qualities and ease of repair. This preference was reinforced recently when we examined an old Bristol 27 just sold by a friend. The surveyor noticed dampness near the bottom of the leading edge of the keel, which showed slight external damage. Probing the loose putty revealed some abrasion of the glass keel molding. In order to sell the boat, it was necessary to grind away a large portion of the glass at the front of the keel, dry out the ballast, and reglass the lead—a job that took several days of work and cost our friend a fair chunk of money.Much of the boat’s interior structure is plywood, glassed to the hull. Fillet bonding is neat and workmanlike with no rough edges to be found.Chainplates are conventional stainless steel flat bar, bolted to bulkheads and plywood gussets in the main cabin. These are properly backed with stainless steel pads. Due to the fact that the hull is lined throughout with a carpet-like synthetic material, it is not possible to examine the bonding of the chainplate knees to the hull. The stemhead fitting is a stainless steel weldment, through bolted to the deck and hull and reinforced inside the hull with a stainless steel gusset to prevent deflection of the deck from the pull aft of the headstay. We’d like to see a metal backup pad behind this fitting rather than the washers which are used.General construction is thoughtful and well executed, with excellent glasswork, a strong and simple hull-to-deck joint, and reasonably installed hardware and fittings.Handling Under PowerAlthough some early models of the 8.5 used a seven horsepower BMW diesel, the 1982 version employs an eight horsepower Yanmar. These small Yanmars are quite impressive, light in weight and far smoother than the company’s older rockcrushers.Because of the high freeboard and considerable windage of the 8.5, the standard engine is the absolute minimum power plant for the boat. Recognizing this fact, the company offered a 15 horsepower, two-cylinder Yanmar as an option. For another 75 pounds and $1,150, we would want this option on the boat if the ability to get places under power is a real consideration.The extra fuel consumption of the larger engine will scarcely be noticed. The 18 gallon aluminum fuel tank will probably give a range under power of over 250 miles—more than adequate for a 28 foot cruising boat.The fuel tank is located under the cockpit and is securely mounted and properly grounded. There is an easily reached fuel shut off between the engine and tank. Unfortunately, the fuel fill is located in the cockpit sole. Spilled diesel oil turns even the best fiberglass nonskid into an ice skating rink. Fuel fills should be located on deck, where spills can be efficiently washed away.Engine access is via a large removable panel on the inboard face of the quarterberth. This panel lacks any kind of handhold to make it easily removable, which will discourage regular checking of the engine oil. The top companionway step also removes for access, but it’s a long reach to the dipstick.There is no oil pan under the engine. It will be necessary to be very careful when changing oil to keep the bilge clean. We have yet to see anyone change oil and filters on a boat engine without spilling something.With the quarterberth panel removed, access for routine service is excellent. The quarterberth has remarkable headroom over, so that the mechanic will not feel like a trapped spelunker after a half hour of work. Engine removal will require some joinerwork disassembly.Handling Under SailThe S2 8.5 is no slug under sail. Her PHRF rating of 174 to 180 compares very favorably to other boats of her size and type. The Sabre 28, for example, has a rating of 198. The Pearson 28 about 195, and the O’Day 28 about 198.Part of this is no doubt due to the fact that the standard sails on the boat come from the North loft. While North’s OEM sails may not be the vertical cut Mylar-Kevlar wonders that adorn custom boats, they’re a lot better than most.S2 now uses Hall spars. The simple masthead rig is extremely clean, with airfoil spreaders and internal tangs. The boom features an internal outhaul and provision for two internally-led reefing lines, with cam cleats at the forward end of the boom.The deck-stepped mast is mounted in a stainless steel deck plate incorporating plenty of holes for the attachment of blocks. Halyards and Cunningham lead aft along the cabin house top to a pair of Lewmar #8 winches. Lewmar #16s are optional, but hardly necessary.The main is controlled by a six-part Harken rig mounted on the end of the boom, and a Kenyon traveler mounted on the aft cockpit coaming. This will work fine with the tiller-steered version of the boat. With wheel steering, the mainsheet is likely to be a nuisance to the helmsman.Because of the end-of-boom sheeting, a boom vang will be essential for full mainsail control. Ironically, the boat’s drawings show almost mid-boom sheeting, with the traveler mounted on the bridgedeck at the forward end of the cockpit. This is probably a better arrangement, although it heavily loads the center of the boom and requires more sheeting force.Owners of 8.5s have little but praise for the interior of the boat. The cabin has a wide feeling, created by pushing everything outboard. The “chart area” on the plan is a myth, as far as we can tell.Despite the fact that the shrouds are set well in from the rail, the boat lacks inboard headsail tracks. Rather, you are limited to snatch blocks shackled to the toerail track. A six-foot piece of track set inboard of the rail would be a useful addition.Standard headsail sheet winches are two-speed Lewmar #30s. Options include both larger winches and self-tailers, both of which are worth considering for either racing or cruising. The cockpit coamings are wide enough for mounting larger primaries and secondaries.The high-quality rig and sails add to the price of the S2, but they are additions well worth the cost.Deck LayoutThe deck layout of the 8.5 is clean and functional, with no toe stubbers to catch you unawares. There are two foredeck mooring cleats, but no bow chocks. The necessity to lead an anchor line well off the boat’s centerline, coupled with high freeboard forward, is likely to result in a boat which sails around on her anchor or mooring. The 8.5 has a pair of wide stainless steel chafing strips at the bow which will greatly protect the deck from the chafe of the anchor line.The 8.5’s foredeck anchor well is one of the best we’ve seen. It is shallow—just deep enough to hold an anchor and adequate rode. There are double scuppers, which offer less likelihood of clogging. The lid is held on by a full-length piano hinge, and there is a positive latch.The shallow locker well above the waterline means that water is less likely to enter through the scuppers, which can be a real problem with a deep anchor well. When the bow pitches into waves, a deep anchor well can fill with water, and if the scuppers clog with debris, you can find yourself sailing around with several hundred pounds of extra weight in the worst possible position. There is no provision for securing the bitter end of the anchor rode, but a big galvanized eyebolt installed in the well by the owner will solve that one.The running lights leave something to be desired. Their location at deck level just aft of the stem makes them vulnerable to damage when handling ground tackle. We much prefer an international style bicolor mounted on the pulpit, another two feet off the water: easier to see, and out of the way. Wiring for the running lights is exposed in the anchor well, and should be secured out of the way.A recessed teak handrail runs the full length of the cabin trunk, serving the dual function of heavy weather handhold and cabin trim piece. Its shape makes it far easier to oil or varnish than the conventional round handrail, although the wide, flat section seems somewhat awkward after years of grabbing round rails.The 8.5’s cockpit is the maximum size we’d want to see on a boat of this size. The T-shape is designed to accommodate the optional wheel steerer, yielding a somewhat odd layout for the tiller-steered version. A bench seat spans the aft end of the cockpit. Although this makes good seating in port, we doubt that you’d want anyone sitting there under sail: too much weight in the end of the boat. It does make a natural helmsman’s seat for wheel steering.The engine controls and instrument panel are also located at the aft end of the cockpit, and are basically inaccessible to the helmsman of a tiller-steered version.There are two lifting lids in the aft cockpit bench, giving access to a cavernous space under the cockpit. To be useful, dacron bags should be fitted to the inside of these lockers. Then, they’ll be handy stowage for spare sheets and blocks.There are comfortable contoured seats along each side of the cockpit, with a huge locker under the port seat. Although plywood pen boards somewhat separate this locker from the engine space under the cockpit, it would be far too easy for deeply piled junk to get knocked over the board and into the engine. This locker should be partitioned into smaller spaces unless it is to be used exclusively as a sail locker.The battery boxes, fitted at the forward end of the locker, could benefit from plywood or fiberglass lids to keep battery acid off gear which might find its way onto the batteries. The box is designed to take two batteries—one battery is standard—stored in plastic containers. A single lid covering the whole box would be more efficient.The huge cockpit will accommodate up to six for sailing, and eight for in-port partying. The cockpit seat bottoms are contoured, and the cockpit coamings slope outboard for more comfortable seating. However, the seats are both too narrow and too short for sleeping.The forward end of the cockpit is protected by a narrow bridgedeck. However, the cockpit coatings extend a full foot above the level of the bridgedeck, To block the companionway to the level of the top of the coamings will require leaving two of the three drop boards in place when sailing.Although there is moderate taper to the sides of the companionway, making it easier to remove the drop boards, it is still necessary to lift each board about five inches before it can be removed. This is far safer than many tapered companionways, where boards practically fall out if you look at them wrong. The companionway slide is one of the best we’ve seen. It’s a contoured piece of acrylic fitted with a convenient grabrail. It slides easily in extruded aluminum channels, and is fitted with a fiberglass storm hood. As on many boats, the aft cabin bulkhead slopes forward, rendering it impossible to leave the drop boards out for ventilation when it rains.BelowdecksOwners consistently praise the interior design and finishing of S2 sailboats. From looking at the 8.5, it’s pretty easy to see why.There are no exposed interior fiberglass surfaces except the head floor pan molding. The hull and cabin overhead are lined with a carpet-like synthetic fabric. While this will undoubtedly cut down on condensation, we at first wondered how this fabric would hold up over time. Inevitably, the hull liner and even the overhead will get wet. In freshwater areas, this is no problem. The water will eventually evaporate. In salt water, however, wet fabric never seems to dry. Salt draws moisture like a magnet draws steel. Since first seeing this boat, however, we’ve had good experiences with the fabric. Be sure, however, to get a good wet-or-dry vacuum to keep it clean.Interior layout is fairly conventional, with Vberths forward, and immediately aft, a full width head. The head can be closed off from both the forward cabin and the main cabin with solid doors—a real luxury in a boat this size. There is a large hanging locker in the head, and reasonable storage space for toilet articles.The word for the main cabin is “wide,” with the settees pushed as far outboard as they can go. Décor is a little heavy on the teak for our taste, but it is one of the better coordinated interiors we have seen. S2 had a good interior decorator.A fold-down dining table seats four. When folded against the bulkhead, it is held in place by a single latch, which makes us nervous.Neither settee is full length. The foot of the port settee runs under the galley counter, making it long enough for sleeping, although your feet may feel a little claustrophobic in the tiny footwell.The starboard settee is an unusual configuration. The aftermost 12" of the settee folds up to form an arm rest, leaving a gap between the end of the settee and the head of the quarterberth.Inexplicably, this gap is referred to on the accommodation plan as a “charting area,” although there is neither a standard nor an optional chart table. It’s sort of like the designer ran out of energy before completing the interior design.Over the non-existent “charting area” is the best electrical panel we’ve seen on a 28 foot boat. The panel has a locking battery switch, battery test meter, and a panel with room for 14 circuit breakers, although only half are installed on the standard boat.The space is welcome, since with the proliferation of marine electronics most electrical panels are woefully inadequate.Most quarterberths tend to induce claustrophobia. That of the 8.5 is more likely to exacerbate any tendencies you might have to agoraphobia. At last, a quarterberth which will not give you a concussion when you sit bolt upright in the middle of the night after your neighbor drags down on you in a wind shift.The standard main cabin sole is carpet-covered fiberglass. For an additional $325, teak and holly was available for the traditionalist. We’d want it. Unfortunately there is no access to the bilge in the main cabin. None. This is inexcusable, and could be dangerous. A few hours with a saber saw should solve this rather basic problem.The galley is workable and accessible, with no awkward posturing required to do the dishes. The sink gets an A+. It is a full nine inches deep, is large enough to take a frying pan, and mounted close to the centerline.In contrast, the icebox gets a C-. It is larger than normal on a boat of this size, but it drains to the bilge, has a poorly insulated top, and a tiny, uninsulated hatch without a trace of a gasket. Boo.Because of limited counter space, the two burner Kenyon alcohol stove is mounted athwartships, rather than fore and aft. This means that the stove cannot be gimballed, and that it is necessary to reach across the inboard burner to reach the outboard one. Given the fact that countertop gimballed stoves are usually dangerous, the lack of gimballing doesn’t bother us much. What does bother us is that if you want to upgrade the stove to something more functional, the limited space allocated will stretch your ingenuity.A fold down table at the end of the galley counter gives additional counter space, but it must be left up in order to use the port settee for sleeping.Roominess, excellent execution, and good color coordination are trademarks of the interiors of all S2s, and the 8.5 fits well into this enviable tradition.ConclusionsThe S2 8.5 is a good boat for cruising the Great Lakes or any coast in comfort and a certain amount of style. Her appearance may be a little modern for traditionalists, with her straight sheer and European-style cabin windows.Pricey? Yes, but when you look at the things that go into the boat—the rig, good sails, and a comfortable, well finished interior—the price may seem a bit less painful. You still pay for what you get.
ENDEAVOUR 33 SAILBOAT 1984
$19,500
Rome, New York
Year -
Make -
Model -
Category -
Length -
Posted Over 1 Month
Classic, fast shoal draft cruiser with rich teak interior, AC and heat, and lots of extras. Spacious salon. If you are in the market for your first family sailboat or looking for a vessel to explore the coastal US, then you need to see this sturdy 1984 Endeavour sailboat. Traditional layout, comfortable and ready to explore. Good setup for the solo sailor. She would also make a very nice live aboard! Current yard rent paid until October 2014. Family illness forces sale. SPECIFICATIONS LOA: 32' 7" LWL: 27' 6" Beam: 11' 6" Draft: 4' 6" Displ.: 11,350 lbs. Ballast: 4,600 lbs. enclosed lead Mast Height above DWL: 48' 9" Rigging: Masthead Sloop Sail Area: 539.5 sq. ft. Main Sail Area: 228.15 sq. ft. Fore Sail Area: (100%) 310.5 sq. ft. SA/D: 17.09 B/D: 40.50 % D/L: 244 Hull Speed: 7.3 knots PHRF - Northeast: 156 Designer: Bruce Kelley Fuel Capacity: 36 gallons Fresh Water Capacity: Approx. 56 gallons Holding Tank: 12.5 gallonsACCOMMODATIONS Spacious Saloon with beautiful solid teak doors and cabinetry throughout. Traditional layout in good condition. V-Berth forward. Salon features L-shaped port settee (converts to double) with a fold away table and starboard bench settee. Single quarter berth & navigation table to port. Galley to starboard. · Nav. Station: Flip Top chart table at forward edge of Quarter berth, three drawers, Rolled chart storage · Head: Located aft of the master to port with vanity, holding tank, head, sun shower, bulkhead mirror, three lockers, drawer, fiddled shelf storage and screened port · Teak bulkhead mounted table with hinged extension and bookshelf/cabinet behind. · Blue upholstered settees/berths in good shape · Generous lighting throughout. TV/FM coaxial cable wiring at shelf over hanging locker · Berths: 6 · Headroom: 6' 2" ENGINE & MECHANICAL · Yanmar 3GM30F Diesel, fresh water cooled, professionally and regularly maintained. · Engine hours: 1,625. · Racor fuel filter · Dripless stuffing box · 3-blade bronze prop, serviced · 36 gallon, welded aluminum fuel oil tank HULL & DECK · Solid KlegeCell foam core decks (no balsa to rot), no soft spots anywhere. No hull blisters. · Skeg mounted rudder for directional stability and strength · Anchor roller at bow · Bruce anchor w/ chain, 200’ 5/8” rode in deep bow locker, excellent condition · Secondary Danforth anchor with chain & rode · Teak hand rails · Anodized aluminum toe rails · Propane deck locker, stbd., with aluminum tank, manual & electric shut-off · West Marine propane kettle grill and canvas cover-like new · Outboard motor mount · Custom foam cockpit cushions · S/S swim ladder · Boarding gates P & S · Fenders & dock lines · Cockpit Speakers · Companionway teak boards, refinished, stow in stbd. lazarette storage pockets. · Companionway swing doors, removable (need repair HELM · Edson pedestal w/38" SS destroyer wheel with 2 instrument pods · 5” Danforth compass in SS hood · Teak folding cockpit table · Removable Edson teak drink caddy SAFETY · Type III PFD's · LifeSling · CO Monitor · Fire Extinguishers · Flare kit · 12V Bilge Pump · Manual bilge pump · First Aid Kit SALON · Spacious interior layout with large fold-out table (shelves behind) · Abundant drawer and locker storage throughout. · 10 opening ports & two large overhead hatches · Teak & holly sole in good condition · Several 12v lighting fixtures · 12 volt fan · 1 Wood framed companionway screen · 1 Wood framed hatch screen GALLEY · SS Galley Maid propane stove and oven · Large icebox with shelves · Adler Barbour 12V refrigeration · SS Sink with H/C pressure water · Microwave oven · Flo-Jet 12 Volt electric water pump, demand type with an accumulator tank. · Whale foot operated water pump in the galley (needs mounting). · Beautiful solid teak stove-top/cutting board with green Silestone insert, with storage slot · Built-in plate and utensil storage · Wine glass rack · Cookware and tableware V-BERTH · V-berth 6'6" · 12 V fan & Solar powered vent fan in hatch · 1 Wood framed Hatch screen · 2 drawers, 2 side shelves & cabinet HEAD · Enclosed head with shower & sump pump · SS sink with hot & cold pressure water · Teak cabinets and storage · Holding tank monitor · Holding Tank: 12.5 gallons with Y-valve and pump-out ELECTRONICS · Autohelm with hand-held remote · West Marine VHF580 Radio · Depth Sounder · Knot meter · Aiwa 40 watt Stereo FM/AM/Aux input with 2 interior KLH speakers and 2 cockpit speakers · Mast-mounted TV-FM antenna · Mast-top VHF antenna ELECTRICAL · 12,000 BTU CruisAir Air conditioning / heating · Breaker Panel: 12 volt DC; 110 volt AC · 4 Batteries (2-12V, 2-6V) · Battery isolator · Xantrex 40Watt multistage battery charger · 110 volt 30A Ship-to-shore cable - 50 ft. · Seaward SS water heater, 6 gallon, 115 VAC/ heat exchanger. · 2 Mast-mounted P&S deck lights · Chart table gooseneck light - red · Brinkman Q-Beam 12V Spotlight, 400,000 CP CANVAS · Two-part full-deck awning/sun-shade (a $1,400 item) · Bimini on SS frame · Helm cover · Sail Cover · Winch covers · SS dodger frame-no canvas STANDING RIGGING · Hood roller furling on head stay · SS wire standing rigging & chain plates · Four (4) each port & stbd. shrouds · Keel-stepped aluminum spar-Exc. Cond. RUNNING RIGGING · Two (2) Lewmar No. 43 two speed self-tailing primary winches w/covers. · Two (2) Lewmar No. 8 single speed mast mount halyard winches. · 2 winch handles · Harken 4:1 ball-bearing mid-boom mainsheet traveler, cabin mounted · Hardware in place / sail cover designed for lazy-jack system. Needs lines. · Genoa tracks with twin-sheet Schaeffer blocks, port and stbd. · Dacron braid sheets · Dacron braid halyards, internal & external, outhaul & topping lift · Aft turning (cheek) blocks port & stbd. SAILS · Footless main sail - new and unused · Original main sail · Genoa head sail - roller furling with UV stripe FRESH WATER TANKS · Polypropylene tank mounted below the stbd. settee, 36 gallons · Polypropylene tank located under port side aft quarter berth, est. 20 gallons, w/ separate deck fillSPARES / EXTRAS / OTHER · Includes 5 Hostar stackable jack stands for off-season layup ($1,000 value) · 4 – 10”x10”x2’ Hickory staging blocks · New Beckson port screens · Tool set in drawer · Hatch WindScoop for ventilation · Stern flagstaff & flag · All manuals, incl. Yanmar · 115VAC Vacuum cleaner · New extra odor-resistant hose for sanitary plumbing · Deck brush, cabin brush and dust pan · Boat hook · Custom compact winter cover scaffolding-ready for tarp (shown in photos) · V-belts, engine hoses, hardware, etc. RECENT UPGRADES INCLUDE · Brand new main sail - never used · Epoxy hull re-faring · Cushions covers removed, cleaned & repaired · Compass serviced · Holding tank seal maintenance, cleanout and sanitizing · New shaft zinc · Bottom paint (9/2014) · Hull polish & wax (9/2014) Work Needed: Woodwork around forward port lights in main salon needs to be repaired/replaced. Bright work: hand rails, cockpit table and taffrailNew price reflects work needed on rudder. Recent repair did not work to seal it and there is water inside. SS rudder post is good and rudder seems solid, is probably serviceable but may ultimately need better repair or replacement. Price: US $ 19,500Located in Rome, NY on the Erie Canal (accessible to Lake Champlain, the Atlantic Ocean or the Great Lakes). This vessel is sold AS IS, WHERE IS.Not included / Negotiable: 8.5' Zodiac/West Marine dinghy, RU260, with oars, pump, bag, repair kit, plus 3.3 hp Mercury outboard - excellent. $950New-in-box Lewmar 1000 Pro-Series 12V Windlass, Stainless Steel. $700Pair (2) of new Lewmar Ocean Series 16CST Self-Tailing Winches, Chromed Bronze. $950 Call: 315-733-7305 (H) Text: 315-368-4939 (C) Email: [email protected] Endeavour 33: http://www.endeavourowners.com/boats/e33/e33brochure.pdf http://sailboatdata.com/viewrecord.asp?class_id=1878 http://sailboatdata.com/view_builder.asp?builder_id=27 http://sailboatdata.com/view_designer.asp?designer_id=162 Zodiac/WM RU-260 Inflatable “Roll-Up” Dinghy: https://www.youtube.com/watch?v=Z0FSSffq5zM http://www.inriodulce.com/lostandfound/RU260.html Mercury 3.3 hp Outboard: https://www.youtube.com/watch?v=MLY-tuSCkK4 http://www.mercury-marine.eu/mercury/en/Products/Products.aspx?Model=TwoStroke%203.3 Lewmar Winch 16CST: http://lewmar.com/products.asp?id=8150&lid=25361
ENDEAVOUR 33 SAILBOAT 1984
$26,500
Rome, New York
Year -
Make -
Model -
Category -
Length -
Posted Over 1 Month
Classic, fast shoal draft cruiser with rich teak interior, AC and heat, and lots of extras. Spacious salon. If you are in the market for your first family sailboat or looking for a vessel to explore the coastal US, then you need to see this sturdy 1984 Endeavour sailboat. Traditional layout, comfortable and ready to explore. Good setup for the solo sailor. She would also make a very nice live aboard! Current yard rent paid until October 2014. Family illness forces sale. SPECIFICATIONS LOA: 32' 7" LWL: 27' 6" Beam: 11' 6" Draft: 4' 6" Displ.: 11,350 lbs. Ballast: 4,600 lbs. enclosed lead Mast Height above DWL: 48' 9" Rigging: Masthead Sloop Sail Area: 539.5 sq. ft. Main Sail Area: 228.15 sq. ft. Fore Sail Area: (100%) 310.5 sq. ft. SA/D: 17.09 B/D: 40.50 % D/L: 244 Hull Speed: 7.3 knots PHRF - Northeast: 156 Designer: Bruce Kelley Fuel Capacity: 36 gallons Fresh Water Capacity: Approx. 56 gallons Holding Tank: 12.5 gallonsACCOMMODATIONS Spacious Saloon with beautiful solid teak doors and cabinetry throughout. Traditional layout in good condition. V-Berth forward. Salon features L-shaped port settee (converts to double) with a fold away table and starboard bench settee. Single quarter berth & navigation table to port. Galley to starboard. · Nav. Station: Flip Top chart table at forward edge of Quarter berth, three drawers, Rolled chart storage · Head: Located aft of the master to port with vanity, holding tank, head, sun shower, bulkhead mirror, three lockers, drawer, fiddled shelf storage and screened port · Teak bulkhead mounted table with hinged extension and bookshelf/cabinet behind. · Blue upholstered settees/berths in good shape · Generous lighting throughout. TV/FM coaxial cable wiring at shelf over hanging locker · Berths: 6 · Headroom: 6' 2" ENGINE & MECHANICAL · Yanmar 3GM30F Diesel, fresh water cooled, professionally and regularly maintained. · Engine hours: 1,625. · Racor fuel filter · Dripless stuffing box · 3-blade bronze prop, serviced · 36 gallon, welded aluminum fuel oil tank HULL & DECK · Solid KlegeCell foam core decks (no balsa to rot), no soft spots anywhere. No hull blisters. · Skeg mounted rudder for directional stability and strength · Anchor roller at bow · Bruce anchor w/ chain, 200’ 5/8” rode in deep bow locker, excellent condition · Secondary Danforth anchor with chain & rode · Teak hand rails · Anodized aluminum toe rails · Propane deck locker, stbd., with aluminum tank, manual & electric shut-off · West Marine propane kettle grill and canvas cover-like new · Outboard motor mount · Custom foam cockpit cushions · S/S swim ladder · Boarding gates P & S · Fenders & dock lines · Cockpit Speakers · Companionway teak boards, refinished, stow in stbd. lazarette storage pockets. · Companionway swing doors, removable (need repair HELM · Edson pedestal w/38" SS destroyer wheel with 2 instrument pods · 5” Danforth compass in SS hood · Teak folding cockpit table · Removable Edson teak drink caddy SAFETY · Type III PFD's · LifeSling · CO Monitor · Fire Extinguishers · Flare kit · 12V Bilge Pump · Manual bilge pump · First Aid Kit SALON · Spacious interior layout with large fold-out table (shelves behind) · Abundant drawer and locker storage throughout. · 10 opening ports & two large overhead hatches · Teak & holly sole in good condition · Several 12v lighting fixtures · 12 volt fan · 1 Wood framed companionway screen · 1 Wood framed hatch screen GALLEY · SS Galley Maid propane stove and oven · Large icebox with shelves · Adler Barbour 12V refrigeration · SS Sink with H/C pressure water · Microwave oven · Flo-Jet 12 Volt electric water pump, demand type with an accumulator tank. · Whale foot operated water pump in the galley (needs mounting). · Beautiful solid teak stove-top/cutting board with green Silestone insert, with storage slot · Built-in plate and utensil storage · Wine glass rack · Cookware and tableware V-BERTH · V-berth 6'6" · 12 V fan & Solar powered vent fan in hatch · 1 Wood framed Hatch screen · 2 drawers, 2 side shelves & cabinet HEAD · Enclosed head with shower & sump pump · SS sink with hot & cold pressure water · Teak cabinets and storage · Holding tank monitor · Holding Tank: 12.5 gallons with Y-valve and pump-out ELECTRONICS · Autohelm with hand-held remote · West Marine VHF580 Radio · Depth Sounder · Knot meter · Aiwa 40 watt Stereo FM/AM/Aux input with 2 interior KLH speakers and 2 cockpit speakers · Mast-mounted TV-FM antenna · Mast-top VHF antenna ELECTRICAL · 12,000 BTU CruisAir Air conditioning / heating · Breaker Panel: 12 volt DC; 110 volt AC · 4 Batteries (2-12V, 2-6V) · Battery isolator · Xantrex 40Watt multistage battery charger · 110 volt 30A Ship-to-shore cable - 50 ft. · Seaward SS water heater, 6 gallon, 115 VAC/ heat exchanger. · 2 Mast-mounted P&S deck lights · Chart table gooseneck light - red · Brinkman Q-Beam 12V Spotlight, 400,000 CP CANVAS · Two-part full-deck awning/sun-shade (a $1,400 item) · Bimini on SS frame · Helm cover · Sail Cover · Winch covers · SS dodger frame-no canvas STANDING RIGGING · Hood roller furling on head stay · SS wire standing rigging & chain plates · Four (4) each port & stbd. shrouds · Keel-stepped aluminum spar-Exc. Cond. RUNNING RIGGING · Two (2) Lewmar No. 43 two speed self-tailing primary winches w/covers. · Two (2) Lewmar No. 8 single speed mast mount halyard winches. · 2 winch handles · Harken 4:1 ball-bearing mid-boom mainsheet traveler, cabin mounted · Hardware in place / sail cover designed for lazy-jack system. Needs lines. · Genoa tracks with twin-sheet Schaeffer blocks, port and stbd. · Dacron braid sheets · Dacron braid halyards, internal & external, outhaul & topping lift · Aft turning (cheek) blocks port & stbd. SAILS · Footless main sail - new and unused · Original main sail · Genoa head sail - roller furling with UV stripe FRESH WATER TANKS · Polypropylene tank mounted below the stbd. settee, 36 gallons · Polypropylene tank located under port side aft quarter berth, est. 20 gallons, w/ separate deck fillSPARES / EXTRAS / OTHER · Includes 5 Hostar stackable jack stands for off-season layup ($1,000 value) · 4 – 10”x10”x2’ Hickory staging blocks · New Beckson port screens · Tool set in drawer · Hatch WindScoop for ventilation · Stern flagstaff & flag · All manuals, incl. Yanmar · 115VAC Vacuum cleaner · New extra odor-resistant hose for sanitary plumbing · Deck brush, cabin brush and dust pan · Boat hook · Custom compact winter cover scaffolding-ready for tarp (shown in photos) · V-belts, engine hoses, hardware, etc. RECENT UPGRADES INCLUDE · Brand new main sail - never used · Epoxy hull re-faring · Cushions covers removed, cleaned & repaired · Compass serviced · Holding tank seal maintenance, cleanout and sanitizing · New shaft zinc · Bottom paint (9/2014) · Hull polish & wax (9/2014) Work Needed: Woodwork around forward port lights in main salon needs to be repaired/replaced. Bright work: hand rails, cockpit table and taffrail.Price: US $ 26,500Located in Rome, NY on the Erie Canal (accessible to Lake Champlain, the Atlantic Ocean or the Great Lakes). This vessel is sold AS IS, WHERE IS.Not included / Negotiable: 8.5' Zodiac/West Marine dinghy, RU260, with oars, pump, bag, repair kit, plus 3.3 hp Mercury outboard - excellent. $1,200New-in-box Lewmar 1000 Pro-Series 12V Windlass, Stainless Steel. $700Pair (2) of new Lewmar Ocean Series 16CST Self-Tailing Winches, Chromed Bronze. $950 Call: 315-733-7305 (H) Text: 315-368-4939 (C) Email: [email protected] Endeavour 33: http://www.endeavourowners.com/boats/e33/e33brochure.pdf http://sailboatdata.com/viewrecord.asp?class_id=1878 http://sailboatdata.com/view_builder.asp?builder_id=27 http://sailboatdata.com/view_designer.asp?designer_id=162 Zodiac/WM RU-260 Inflatable “Roll-Up” Dinghy: https://www.youtube.com/watch?v=Z0FSSffq5zM http://www.inriodulce.com/lostandfound/RU260.html Mercury 3.3 hp Outboard: https://www.youtube.com/watch?v=MLY-tuSCkK4 http://www.mercury-marine.eu/mercury/en/Products/Products.aspx?Model=TwoStroke%203.3 Lewmar Winch 16CST: http://lewmar.com/products.asp?id=8150&lid=25361
Rebel 16 Mark II Sailboat with Aluminum Trailer
$999
Angola, Indiana
Year -
Make -
Model -
Category Daysailer Sailboats
Length 16.6'
Posted Over 1 Month
Stable fiberglass sailing boat carries six people (or 1170 pounds). Includes trailer, full rigging, and TWO suits of sails. One suit of sails is in like new condition, the other set is in very good condition. Serial number 1929 (built in late sixties to early seventies I believe). The centerboard swings up into the cockpit, so you can change the depth to dock in shallow water. The rudder also swivels up if it hits an obstruction. The trolling motor in the photos is not included. There is, however a permanent motor mount on the stern. The boat will take up to a 5hp motor, but my 30lb. thrust trolling motor drives it around just fine. The boat is located on West Otter Lake, Angola, IN. Buyer with the selling price in cash or Pay Pal payment can drive it away. (Trailer takes an 1 7/8" ball hitch.) The following article from Sailing Magazine gives a great description of Rebel sailboats. You can access the original on SailingMagazine.net. Rebel 16 2008 January 8 By Staff This nimble and tough classic is perfect for a daysail or a day of racing This year the boat that holds claim to being America's first production fiberglass one-design will celebrate its 60th birthday. That the boat is still in production makes this milestone that much more remarkable. In 1948, fresh out of the Navy, Ray Greene began building a 16-foot family daysailer out of his Toledo, Ohio, shop using a revolutionary new material called fiberglass. The design of the boat was based on lines drawn by a local high school drawing instructor by the name of Alvin Younquist. With its wide, 6-foot, 7-inch beam and 110-pound steel centerboard the stable little boat known as the Rebel soon became a hit on the Midwest's inland lakes. And while Greene said he never intended to create a racer, thanks to the boat's performance-courtesy of a large 120-square-foot main and 46-square-foot jib on a fractional rig-it wasn't long before a competitive structure was built around the boat. By 1952 a class association had been firmly established and by 1963 the class boasted 138 active members. Not bad. Fleets started popping up across the Midwest, south into Kentucky and all the way down to Texas. Meanwhile, class members could be found sailing the inland lakes of the Eastern Seaboard from New York to Florida. After 25 years of building the Rebel, with more than 3,000 hulls produced, Greene was ready to call it quits and sold the works to a group of Chicago investors. Production of the Rebel continued at a steady pace during the 1970s, and was done under a number of names: Melling Tool Co., Rebel Industries and finally Spindrift One Designs. After Spindrift folded, the Rebel moved to Michigan in 1988 when Nickels Boat Works of Fenton took over with the production of the Mark V model. Nickels continues to build the Rebel, offering buyers a choice of a daysailer version for $9,860 or the optimum racing version for $11,872 less sails and trailer. A stainless steel centerboard now comes standard with the Rebel. Nickels also continues to be a great source for parts and accessories, as well as information, on the Rebel. One tough Rebel While there have been reports of problems with the foam flotation on older boats becoming waterlogged, that has been less of a problem on boats from the 1970s and later. Other than that, a buyer of a used Rebel should find few issues with the condition of this durable little boat. Indeed, boats 25 years and older will still top regatta leaderboards. "They're well made, very rugged boats that will last forever," said Al Vorel, National Rebel Association Commodore, who has been racing the same boat, No. 3914, for almost 20 years. "You don't have to run out every 5 to 10 years to buy a new boat." This is one of the reasons for the longevity of the class. Boats tend to stay in the family, passed down from parent to child, with the younger generations wanting to keep the racing going. "My mother races, and my daughter sometimes races, so there are times we'll have three generations on the course," Vorel said. This also, of course, keeps a lot of boats off the market, and finding a used Rebel can be a bit of a challenge. But thanks to the Internet, it's possible to locate a few sellers. Prices can vary from just under $1,000 for an older boat in need of some work to $3,000 or more for a later model. Buyers can typically expect to pay in the neighborhood of $1,500 for a pre-Nickels-era boat in good shape. We were fortunate enough to find a late 1970s Rebel listed for sale on www.craigslist.org. Better yet, the seller was within trailering distance. The offer on the boat was $1,400, so we drove out to take a look. The boat was well cared for, kept under a roof winters, and showed no structural damage. Other than some algae stains and scuff marks the finish looked good, and all the gear was there, including the main and jib, which the owner said he bought new about seven years ago. We did see some possible issues, including a rusty, pitted centerboard and a wooden rudder that looked to have some rotting. So we offered to pay the full $1,400 if the owner threw in the trailer, which he originally wanted an extra $200 for. The deal was closed and we drove off with the Rebel in tow. Rebel with a cause With the boat parked in our yard the first item of business we wanted to take care of was the rusty centerboard. Nickels offers a stainless steel replacement board, and we could picture how sweet the boat would look with a shiny new stainless fin. Unfortunately, these centerboards run close to $1,000; more than two-thirds the cost of the entire boat. So such an extravagant purchase didn't make much sense. Instead we set about rehabilitating the old board. We removed, with a bit of difficulty, the 110-pound board and set in on sawhorses. The first step was to remove the old paint using paint stripper, then power sanding. We then slathered on some Duro Naval Jelly to remove the rust, wiping down everything with paper towels then finishing up with a clean, acetone-soaked rag. Next, we filled in the pits and hollows with West Marine Surfacing Putty, and sanded everything smooth. We made certain the blade was fair by running a straight edge along the board. We also further faired the rounded leading edge of the board to within the class rule limits, which prohibit tapering less than 1/16th of an inch and more than one inch in from the leading edge. We then primed the board with several coats of Interlux Primocon primer, which when dried we wet sanded with 400-grit paper, and finished with a couple coats of Interlux VC-17m Extra bottom paint. With the centerboard done, we then turned to the rudder. An ice pick determined the wood was beginning to rot near the lower trailing edge. We probably could have rehabilitated the rudder as well, but since we had saved some money by not replacing the centerboard we decided to spring for a new rudder. We opted for a fiberglass blade, supplied by Nickels for $375. This cost covered just the blade, as the original aluminum rudder cheeks and hardware were still in good shape. While we were on the phone with Nickels, we decided to order all new running rigging to replace the weathered lines the boat came with. This included lines for the cunningham, boom vang, centerboard system, as well as sheets and halyards for both main and jib. The total for 112 feet of ¼-inch line and 105 feet of 5/16-inch line came to $100. Next we took a closer look at the standing rigging. The spars showed no defects, and with a bit of metal polish and elbow grease the rotating mast, boom and aluminum whisker pole looked good as new. The 1-by-9 stainless steel shrouds and forestay also showed no visible defects. We did, however, find the diamond stays on the mast to be tuned rather tight. According to the North Sail's One-Design tuning guide for the Rebel, an overly tight diamond can limit fore and aft mast bend, and can even cause negative pre-bend, where the mast bends forward at the tip. Since we want to have a competitive boat, we loosened the diamond tension and will readjust after doing some sea trials. As we said, we ultimately wanted to race our Rebel and didn't want a slow boat. So obviously the 7-year-old suit of sails had to go. This would be our biggest expense, and a new suit of sails would alone exceed the original cost of the boat. A new main and standard jib (a light air jib is also available) from North Sails set us back $1,615, which included $20 for class royalties but not shipping. Certainly this was a blow to our budget, but we rationalized it by thinking about the fun we would be having with some close racing come summer. Our last order of business was getting our bottom clean and smooth. We first scrubbed the hull down with a detergent then wet sanded everything below the rails to a slick surface with 1,200-grit paper. After a rinse and wipe down with the hose and clean towels we were satisfied we had a slick bottom. We finished off by treating all our hardware and moving bits to a little McLube Sailkote spray. We now have what we feel will be a contender on the course for our racing crew of two. Yet, with the roomy Rebel cockpit that can seat six, we're also looking forward to some lazy summer daysailing when friends and family show up. Either way, we'll certainly get our money's worth from this tough but nimble little classic. LOA 16' 1.5" LWL 15' 10" Beam 6' 7.5" Draft 3' 4" Weight 700 lbs, Sail area 166 sq. ft.
1982 47' Formosa Peterson Center Cockpit Cruiser Sailboat
$67,500
Key West, Florida
Year -
Make -
Model -
Category -
Length -
Posted Over 1 Month
Located on the doorsteps to the Caribbean in Key West Florida.For a full set of pictures and to see some shots from our sailing adventures with the boat visit www.formosa46.com Normal 0 false false false EN-US JA X-NONE Known around the world as one of the fastest center cockpits ever built, this Doug Peterson design offers the offshore cruising layout with a comfortable aft cabin with separate cockpit access as well salon entrance.The forward cabin offers a large V Berth, and Queen size berth in Master, both staterooms offer private adjacent Head Compartments with showers. She is a well maintained example of the beautiful Old World Craftsmanship in the cabinetry and joinery in the varnished teak interior.Bear Sniff has had a multitude of updates including Electronics and Instruments, 500W Wind Generator, Recently Varnished Deck Woodwork, Life Raft, RIB Dinghy With Engine, Asymmetrical Spinnaker, Complete New Running Rigging, New Heads, All Sails Reinforced for Cruising, New Antifouling New Thru Hull Valves, Updated mechanicals and all winches professionally serviced.Please see full specs below for complete details. Bear Sniff is powered by a Ford Lehman 2712E Engine, has Marine 16KBTU Reverse Cycle AC, can sleep six and is a fine example of a world cruiser, or Spacious Liveaboard. With her abundant number of recent upgrades Bear Sniff is a much desired cruiser.Bear Sniff features an offshore curising layout with a comfortable aft cabin with a separate cockpit access hatch as well a salon entrance. The Aft cabin includes a head with shower to port and a spacious double berth.The forward cabin is a large V-Berth with a second head located to port just aft of the cabin with plenty of storage opposite. The Nav Station is located at the aft starboard corner of the salon.The L Shaped Galley is opposite with tile countertops, and the folding dining table seats six, extending the length of the salon. Port and Starboard are comfortable settees that can double as berths. The excellent craftsmanship is apparent in the lovely varnished teak interior throughout plus teak and holly sole. DimensionsLOA: 47 ft 1 inBeam: 13 ft 0 inLWL: 40 ft 0 inLength on Deck: 47 ft 1 inMinimum Draft: 6 ft 3 inMaximum Draft: 6 ft 3 inDisplacement: 33000 lbsBallast: 11330 lbs EnginesEngine 1:Engine Brand: Ford LehmanEngine Model: 2712EEngine Type: InboardEngine/Fuel Type: DieselEngine(s) Total Power: 80 HPTanksFresh Water Tanks: (150 Gallons)Fuel Tanks: (100 Gallons)Holding Tanks: (20 Gallons)AccommodationsNumber of single berths: 2Number of double berths: 2Number of cabins: 2Number of heads: 2Outside Equipment/ExtrasTotal Liferaft Capacity: 6Manual windlassGalleyMicrowave Oven Kenyon Marine Stove with Oven12V Refrigeration with frost condenser & Super cool Air cooled compressorHot/Cold Pressure Fresh WaterFull Kitchen UtensilsNew Water Pressure Pump(2) Vacuum CleanersNew Potable Water Filter(4) Cabin FansRoom Air Filter(4) Cabin Pillows(4)Sets of Blankets & PillowsFull Galleyware of pots, plates, cups etc.(2) Deep S/S Sinks Electrical8KW 110V Westerbeke Genset (rebuilt 2006) New 500 Watt Wind Generator & Battery Charger (not fitted) 110V to 12V Electrical Panel rewired Dec 2012NEW 20 amp Smart Battery Charger(2) Group 29 House BatteriesGroup 29 Engine Start BatteriesGroup 27 Gen-Set Battery(2) 30 amp Shore Power CordsBluetooth Stereo12V & 110V Electrical Panel Recently Rewired(4) Cabin Fans (not fitted) ElectronicsEPIRBAIS & DSC VHF and New AntennaeRaymarine Smart Pilot and Hydraulic Autohelm UnitNew Icom Backup VHF M 35 w/New Whip AntennaeMast Antennae Replaced 9-13Raymarine Autopilot (hydraulic drive)NEW 2012 Lowrance HDS-7 Chart Plotter w/ High Resolution Depth SounderRaymarine i70 Smart Display Control UnitB & G Wind, speed, Depth InstrumentsRadar Reflector26” LCD TVBluetooth Stereo/CD PlayerDeckHull antifouled and all anodes replaced (Sept 2013) Danforth Anchor#45 Delta AnchorCQR AnchorSmall Danforth Dinghy AnchorRIB Dinghy w/ 2.5hp EngineFoot Pump for DinghyManual Simpson Lawrence WindlassCockpit TableCockpit PillowsCockpit SpeakersCaptains Chair PillowSix person Offshore Life Raft(2) Inflating offshore Life Jacket w/ Harness(2) Inflating Coastal Life Jackets(2) HarnessesOne set of jacking straps(4) Thru-Hull Valves Replaced 2013All Deck Woodwork re-oiled Sept 2013(4) Sets of Strobe Lights, Whistles, Sea Dye, Glow SticksFull set of Flares, including Flare Gun, Flag & Spare Cartridges(3) NEW Fire Extinguishers(1) New Safety DrogueBimini(5) FendersBarge BoardNumerous Ropes & SheetsBinocularsHammockSails & RiggingComplete New Running Rigging Professionally replaced and installed Dec 2012 Full Batten Quantum Mainsail New 2006, reinforced Dec. 2012 for cruising w/deep second reef point130% Quantum Genoa New 2006, reinforced Dec. 2012Staysail (excellent condition)Asymmetrical spinnaker & BagComplete New Running RiggingSail CoverHarken Roller Furling(4) Winch HandlesS/S Standing RiggingALLWINCHES PROFESSIONALLY SERVICED DEC 2012(2) Barient 32 Two Speed Primary Winches(2) Barlow 25 Two Speed Winches one on Combing, one on Coachhouse(3) Barient 21 Two Speed Winch on Combing(4) Barlow 25 Two Speed Mainsheet WinchBarlow 20, 21, and Aqualast 22 Two Speed Winches on MastEngines & Mechanical80HP Ford Lehman engine7 amp Altenator(2) Fuel Tanks w/Racor Oil/Water Separator (approx 100 gal)(3) Water Tanks (approx 200 gallonsHolding Tank (approx. 30 gallon)Recently refurbished Water Pump Sept. 2013Oil & Filters Changed Every 100 hoursManual and Automatic bilge Pumps110V Air Conditioning(2) Heads Replaced Dec 2012(3) Portable Diesel Tanks(1) Gas TankOil Vacuum PumpMacerator Pump$3000 Full Set of Tools for everything you want to do on boardNumerous Spares (Screws, washers, rope, cable, bilge pumps, impellors, fixtures etc)Full Set of Spare Oil, Fuel, & Water Filters Contact me for a full list of equipment not included in the sale. Mainly personal effects etc. If you have any questions or wish to arrange an inspection feel free to contact me to discuss.________________________________________________________________________________ In answer to the many of the questions posed to me here are a few more details:- I've owned the boat for two years. Initially it was purchased in Houston with big plans to sail the Caribbean but life unfortunately got in the way. During that time I've refit many of the items on the boat and this is outlined above.- Yes the boat can be viewed in Key West, Florida, USA. For those that are interested message me and I'll give you the contact details of my local Key West broker.- The boat is currently Australian registered but will be de-registered as part of the sale. So the new owner can get the boat re-registered with the USCG.- Yes the boat is capable of offshore voyages, but no I wouldn't jump in this tomorrow and sail across the Pacific. Not due to any structural fault in the boat. I would add better water storage, a water maker, fit the wind vane, purchase some spare sails, fit a full bimini cover etc. before committing to such a voyage. Of course you would want to have had a lot of experience offshore before crossing the North Atlantic.- More images of the boat and the trips we've taken can be found at www.formosa46.com- No I will not trade for another boat unless someone has a similar size/condition vessel in Australia.- Yes the price is negotiable within reason as are the sale terms. Please contact me to discuss.- The boat is very well equipped with all the safety gear you could ever hope for and is in a good condition.
1974 C&C 35 Mark II ****SOLD September 2014
$19,900
Tacoma, Washington
Year -
Make -
Model -
Category -
Length -
Posted Over 1 Month
75 C&C 35 mk II Chinook landing marina Rigging and sails, in good condition. Universal diesel in good condition with i about 900 hrs. Many details in description in links. Complete sail inventory of 14 extra sails is available. Only known issues or repairs needed are some wind instruments not working.This a SAILING sailboat, not a floating Winnebago that sails like a bar of soap. For those interested in racing: C&C 35 Mark I's had a PHRF rating of 130, the significantly larger stock Mark II's were said by the designers to rate 125 but sail much better. The Mark II has an 11 inch greater over length, more than 2 and a half FEET longer water line length, more freeboard, and 3,300 lbs greater displacement. Later built 35 Mark III's were down sized to Mark I dimensions , are much lighter built and hardware equipped, and while fast, are a major step backwards in quality in my opinion. Currently racing Mark II's seem to measure 126 to 128 seconds. The early stock 35 mark II's were criticized by some hard core racers looking for a slow rating advantage in a very fast boat. Some thought they were tender, and did not point high enough with huge racing headsails and the standard swept back keel. A number of them were modified with a slightly heavier full fin design with more lateral area that was a huge improvement in performance and handling . We can beat and reach with J-35 boats in the 70 seconds/mile class. We have not had this boat measured, but I expect that the improved keel would penalize the rating a few seconds, small price for the performance gain.This U S Coast Guard documented, 35 foot 6 inch classic cruiser/racer sailboat is one of C & C's most graceful, best built, and best performing designs. She is competitive with much newer and larger boats costing many times her price. Re-engined with low time (690 hr) Universal 3 cylinder 25 HP diesel, professionally rewired electrical system, and new ground fault isolator. Includes 15 Barient heavy duty winches and recently rebuilt main and roller furling cruising genoa. Completely equipped for cruising or club racing this boat comes with everything needed to sail away: electronics, anchors, autopilot, extra cordage, cabin heater, cockpit cushions, life jackets, even Puget Sound charts. This boat has been well maintained and equipped for every contingency. It competed successfully twice in the Victoria to Maui race and is well known and respected in the area. The original owner had a custom keel installed with more lateral area than the stock Mk II design, giving this boat even better stability and windward performance than the standard model's exceptional ability. The last surveys are excellent, with no blisters in her solid glass hull.DRACO RED, 1974 C & C 35 FT MRK II, HULL NO. CCY 35 2890674 LOA 35' 6" WLL 30'3" Beam 10'6" Draft 6' 3" Disp 13,800 Design Ballast 5,620. A custom-built keel fitted. Marconi (sloop) rigged with backstay adjuster, all stainless standing rigging.RECENT MODS AND NEW EQUIPMENT New Boom Kicker boom jack/vang and boom vang 4 part downhaul tackle. Professionally installed 110V ground fault circuit breaker and AC power panel, isolating DC power switch, automatic bilge pump, CO monitor, Petit Ultimate Pro bottom paint this summer. Group 27 and 24 house and starting battery.Fresh water cooled Universal 3 cylinder 25 HP diesel new in 1984. Hours 680. 2 blade 16X10 bronze propellor w/Hurth 2:1 transmission, stainless shaft. Cruises 5+ Kts @ 1800 RPM and about 1/2 gallon per hour, 6.5 Kts @2100 RPM at about 3/4 gallon per hour. Stainless fuel tank 20 gallon, fuel filter and water sepator.ELECTRICAL Two batteries w/isolator. Shore power with GF panel , circuit brakers, cable, plug adapter, Newmar automatic battery charger, Danforth battery monitor, Guest galvanic isolator, extra external zinc fish on cable. Icom Marine VHF, Kenyon knotmeter and distance log, repeating distance log at nav station, expanded scale sail trim indicator, two Data Marine depth sounders, kenyon masthead wind speed and direction (inop), Autohelm 3000 autopilot, 3 DC outlets for GPS, IPOD, etc. CO sniffer, Explosive gas fume sniffer, magnetic propane safety valve. Sansui AM/FM Cassette stereo w/ remote speakers. Aquameter galaxy binnacle mounted compass. Boston ships quarts clock and barometer.CANVAS AND RUNNING RIGGING North main, new 83, refurbished 2010. Quantom roller furling 125% cruising genoa, new 04, refurbished w/new sun cover 2010. All sails are excellent . Five total halyards, two topping lifts, down hauls, guys, extra sheets etc. Sturns twin track roller furling. Blue sun shield cover for Main, wheel and binnacle, main hatch,15 winch covers. Jiffy reefing on main with 3 sets of reef cringles, and cunningham. Extra track on mast for storm tri-sail.Edson pedestal destroyer wheel steering with binnacle. Danforth 12H lunch hook w/30 ft chain and 200 ft 3/8 dacron. Danforth 22 with 30 ft chain and 200 ft 1/2 in dacron rode. Bow pulpit with anchor roller, stern pulpit and double lifelines all around. 9 ft inflatable dingy, old but serviceable, Lifesling, life jackets, fitted cockpit cushions, mooring lines, fenders, boson's chair. Running lights, Masthead tricolor, spreader flood, foredeck flood lights. Ships horn and brass bell. Stainless BBQ, Hand held 7x50 monocular bearing compass. Large self bailing cockit w/ cushions and two deep large lazarette lockers. Windscoop for hatch ventilation. Boat hook, boarding ladder, mooring tackle, fenders, etc. Huge invertory spare sheets, snap shackles , parts.All teak interior with over 6 ft head room throughout. Two lexan opening hatches plus main companion way. One opening port light in head. There are two custom deck mounted dorade boxes with cowls for extra ventilation. Forward cabin has comfortable v-birth and ample storage. Raritan head has sink, storage, and teak privacy door. There is large holding tank and Y valve for overboard discharge at sea. There is separate privacy door between forward cabin and salon. Main salon has port dinette and settee, converts to long double berth that's OK for kids or single adult, but close for 2 large adults. Starboard is settee/ very good single berth.There are two hanging lockers that both drain to bilge. Aft on starboard is complete nav station w/power outlet, map light and dedicated table. Aft of that is good single birth. Sleeping for six adults was claimed, five can actually sleep in complete comfort. Lee cloths are include for crew rest while healed underway. A Wallas diesel/kerosine forced air heater is installed. The U shaped galley is to port and has a large ice chest, and several cupboards with good storage and lots of counter space. There is a 3 burner propane stove w/oven, with marinetic propane safety shut off. Fresh water tankage is reported to be 60 gallons. Very nice brass gimbaled kerosene lamp w/spare glass chimney works underway or at anchor. West marine pancake 110v heater/fan, and 110 V cabin fan.SAFETY EQUIPMENT Two installed manual Whale Gusher bilge pumps, Rule electric automatic bige pump, 2 Halon fire extinguishers, Lifesling, rope emergency ladder, flares, 6 life vests. Radar reflector, man overboard pole, floating man overboard strobe, bronze sea cocks on all thru hulls. Sea anchor, first aid kit. Spare tiller back up for wheel steering.14 total sails: (1) North main, new 83, refurbished 2010. (2) Quantum roller furling 125% cruising genoa, new 04, refurbished w/new sun cover 2010. (3)North 80% Storm sail 1980. (4) North 100%, blade jib orig. (5) North 140% 1975. (6) North 150% 1983 Mylar racing genoa. (7) North 2 oz. drifter 1974. (8) North blooper. (9) North tall spinnaker staysail. (10) North 1/2 oz. radial head spinnaker 1976. (11) North 3/4 oz. spinnaker 1974. (12) North 3/4 oz. tri-radial spinnaker. (13) North 1 1/2 oz. spinnaker. (14) North 1 1/2 oz. tri-radial spinnaker 1980. All sails are excellent except oldest 3/4 oz. spinnaker is stiff from sun exposure . Five total halyards, two topping lifts, down hauls, guys, extra sheets etc. Sturns twin track roller furling. Blue sun shield cover for Main, wheel and binnacle, main hatch, 15 winch covers. Jiffy reefing on main with 3 sets of reef cringles, and Cunningham. Extra track on mast for storm tri-sail.Standing rigging was replaced with stainless oversize for blue water Victoria to Maui races and is in excellent condition.There is an old but serviceable 9.5 foot inflatable dingy available. For additional information, reply to this ad or see: http://www.vflyer.com/home/crlk?id=247548010&ps=16 vFlyer ID: 247548010
