Corvette Parts Boats for sale

1-8 of 8

Sort By

1963 wood crackerbox boat

1963 wood crackerbox boat

$21,000

Lacey, Washington

Year -

Make 1957-58 Corvette Running Gear

Model -

Category -

Length -

Posted Over 1 Month

This project was just completed. Features a '58 Corvette 283 with '57 Corvette FI heads, new Edelbrock manifold and 500 cfm carb. Joe Hunt Magneto with Taylor wires. Engine and boat have test time only, 1 hour, 56 minutes total. a complete running log book will be furnished to the buyer. Vintage Hilborn mechanical fuel injection is available at extra cost. Boat has undergone a complete rebuild, each part or component being either rebuilt, fabricated, or OEM replaced. Marine hardware is Nicson and gaskets were manf. from original templates. Military spec(AN) nuts and bolts throughout. A new aluminum fuel tank was manf. and race foam filled. Seats were made from sheet metal, ribbed, and upholstered in heavy weight vinyl. Mounts are contained in a single piece of oak, aluminum channel reinforced. Seat package removes as one piece.Side exhaust system was built from scratch utilizing aluminum and silicon tubing. Silicon is 5 ply and designed for wet exhaust systems. The entire wiring system was replaced utilizing marine grade components. Each wire is protected with blade circuits. All connections were crimped, soldered and heat shrink wrapped. Gauges are Stewart Warner Wings with electric senders. A master cut off switch is wired directly to the new Optima battery.The bottom was replaced by the previous owner who also rebuilt the engine. He experienced some overheating problems which was a result of a water pump vane disintegrating and plugging the water ports in the block and heads. All the rubber slag was located and removed. Paint is PPG OMNI Urethane over a fiberglas wrap, which was restored before paint. Trailer was restored with new bearings, wheels, tires, wiring, lights, carpets, et al. Red parts are powder coated, and the black is Gator Poly bed liner paint. Please go to www.youtube.com/channel/UCLHNB9ApKb6xW8jpBp5qAwA/feed to see the boat on the water!, $21,000, fob Washington State and will consider partial trades for a project Jersey Skiff, or another project Crackerbox. Delivery to the West Coast will be considered. Boat and trailer have clear titles and registrations.

1973 Chris Craft XK22 Ms JLG Restored Award Winning Rare Corvette 350 engine

1973 Chris Craft XK22 Ms JLG Restored Award Winning Rare Corvette 350 engine

$75,000

Boulder City, Nevada

Year 1973

Make Chris Craft

Model XK22

Category -

Length 22' 9"

Posted Over 1 Month

Very Rare fully restored 1973 Chris Craft XK-22 MS JLG Number 64 of 75 1st Place Winner South Lake Tahoe Wooden Boat Classic 2015 From the moment she traces along the shoreline, it’s clear to many viewers that Ms. JLG is a very special watercraft. As a very rare sport boat assembled with various marine parts and supplies from the original home of the Chris Craft Corporation, Ms. JLG’s hull was fabricated in Pompano Beach, FL, in 1973. Purchased from its second owner in 2004 and brought from its home in Oyster Bay, NY, Ms. JLG was completely restored in Boulder City, NV, by the fall of 2007. The final restoration included a new Gel-coat exterior finish to highlight the boat’s spectacular unique hull design and interior outfitted with the original JLG corporate colors along with fabric patterns to match its 1973 debut. At 22’ 9” long and weighing 3300 lbs., this particular XK22 version from Chris Craft came with the rare 1973 Corvette 350 engine that produces up to 320-horsepower for Ms. JLG. Developed as an ocean-going vessel by world-class hull designer and XK22 project manager, Dick Avery, Ms. JLG was outfitted with the state-of-the-art Volvo 270 Velvet Drive to compliment its powerhouse engine which together propels it to 55 MPH even with a full load of people and gear on board. As additional evidence of Ms. JLG’s rarified status, there were only 220 of these XK22s manufactured by Chris Craft between 1971 and 1976. Actually, Ms. JLG is number 64 of only 75 produced in 1973 and one of the few sport boats outfitted with this special drive package. Please ask any questions before bidding.

1996 Mastercraft 190 ProStar LT1 Corvette Engine with Powerslot Transmission

1996 Mastercraft 190 ProStar LT1 Corvette Engine with Powerslot Transmission

$12,900

Dania Beach, Florida

Year -

Make -

Model -

Category -

Length -

Posted Over 1 Month

Mastercraft ProStar 190 Ski and Wakeboard Boat LT1 Corvette Engine (Electronic Fuel Injection) 350HP Only around 950 hours I am the second owner and I had the boat for around 8 years. I have a clear title under my name and a title for the trailer as well. Powerslot Transmission (1.5:1) It increases the out of the hole shot. It has a stronger 1 1/8" diameter and the propeller is 14" 4 blades 14" Propeller like new (absolutely no dings) one spare 3 blade original 14"x18" propeller. Orca half Closed Cooling System (I have made the conversion about 5 years ago, I have all the parts to convert it back to an original open system) Perfect Pass In Dash New Marine Audio system 4 speakers and tweeters with Marine SubWoofer Depth Finder In Dash SkyPylon for Wakeboarding Two Batteries with Isolator (automatic charging and isolates the engine battery so you do not accidentally drain it) Water Hose Connection for maintaining and starting the boat out of the water Teak Swimming Platform (one extra original fiberglass platform not installed, not in perfect condition) Everything Works Mooring Cover Sunbrella (has a tear of around 30" repaired with duct tape) Bimini top (sunbrella) Serviced every 6 months always with Valvoline VR1 20w50 Oil (this oil has zinc for the cams), I also have a spare water impeller. Mastercraft Trailer with automatic latching The boat is really in very nice condition, however you can find small imperfections in the Vinyl seats (some pictures show a small stain or stitches that are coming off, there is no tears or cuts) and hull. Only minor details as you can expect from a 1996 boat. I will try and upload a few more pics, specially the dashboard showing the exact hours and the propeller. I have the boat in my house, you are more than welcome to inspect it. We can start the engine in my house with the water hook up, however if you want to test it in the water we can go to Markham Park approximately 30min from my house. At this point you will have to be committed to buy the boat provided that it runs as described. So I will need US$100 cash as a deposit to take the boat to the lake. If it does not run as described I will refund the US$100, but if it runs as described and you do not want to buy it I will keep the deposit. I require a deposit of US$500 when the auction finishes and the balance of the full amount within 72 hours and only when the funds are cleared I will release the boat. I require local pick up and only after the funds are cleared (cash would be immediate release).

2002 Malibu Sunsetter LXi - 21 Ft Wake/ski boat

2002 Malibu Sunsetter LXi - 21 Ft Wake/ski boat

$22,500

Madison, Alabama

Year 2002

Make Malibu

Model Sunsetter

Category -

Length 21.0

Posted Over 1 Month

Walk through windshield, 2002 Malibu Ski Boat, It has the Wedge to create a awesome wake board experience. Boat is barely used. Only 194 hours, with 6 hours on new engine. Brand New 310hp Monsoon, previous owner had stored in boat house and the power went out, so entire engine was replaced due to freeze damage, estimate was $7,800 for parts and labor.Interior looks like it has never been used. No Tower, New Bimini Top, Depth Finder, used Boat Cover, teak swim step. Take advantage of a great boat with very low hours and a brand new engine! Nominal Length: 21' Max Draft: 1.5' Engine:310 HP Indmar Monsoon (Corvette Engine) Inboard Draft: 1 ft. 6 in. Beam: 7 ft. 9 in. Fuel tank capacity: 38

Wellcraft SCARAB 33',  twin 540's, trailer, NICE!!

Wellcraft SCARAB 33', twin 540's, trailer, NICE!!

$39,950

Greenacres, Washington

Year 1995

Make Wellcraft

Model SCARAB

Category -

Length 33.0

Posted Over 1 Month

1995 Wellcraft SCARAB Recent exterior paint on sides with Teflon bottom. Motors have less than 80 hours. Aluminum triple axle trailer. Boat is 33' 6" with integrated swim platform from Wellcraft. Very nice boat for the money. $30k in motors alone, all new parts including IMCO exhaust. Great condition inside and out for a 20 year old boat. Looks like a newer boat since the removal of the old graphics. Adult owned cruises 55 at 3100 rpm GPS. WOT only once, 83 GPS on Lake Havasu. Boat does not have hydraulic steering. Boat has been mostly on Coeur d'Alene Lake and is currently stored in Spokane Valley. If you are looking for a boat you don't have to sink thousands of dollars into this would be the one, most updates / upgrades are already done. My loss your gain. I would consider trades of equal value or cash plus trade. Interests would be Street Rod, Corvette, Harley, Porsche etc. Engines: - Twin high performance stroked Mercruiser V8 502s making them 540's (built to push over 600HP each) - Motors were professionally built by Cassell Performance Engines and tuned by Stromberger Performance in Spokane, WA Most everything else was purchased through Boostpower or Teague Custom Marine. - Professionally painted to match boat, trimmed in mostly polished stainless steel - Large Oil coolers, new starters, alternators, - Braided fuel lines - New Imco high flow exhaust - Holley Marine 850 performance carbs - MSD ignition boxes and performance distributors - Thru hull exhaust - 3 New Marine Batteries Outdrives: - Bravo 1 outdrives - Four blade 28p stainless props Interior: Misc: - All new control cables - Drop down bolster seats for sitting or standing - LED Cabin Lighting - Livorsi Billet Controls - Updated Dash Covers: - Mooring Full Storage cover Trailer: 2000 Aluminum triple axle always maintained with newer tires Keywords: Boat, Powerboat, Trailer, Offshore, cigarette, Donzi, Formula , Fountain, Baja

13ft Custom Built Boat Runabout Yacht Tender and Trailer Package

13ft Custom Built Boat Runabout Yacht Tender and Trailer Package

$19,000

Easton, Maryland

Year 2010

Make Dirty Bird Custom Boats

Model Bar Boat

Category -

Length 13.0

Posted Over 1 Month

This is a super cool, super custom hand made boat. Are you looking for that item the guy with everything doesn't have? This is it this boat makes a great tender, runabout for running to dinner, or for drinks, or taking off to the nearest sand bar. This is the only one built with these colors. Boat is new never titled and you are purchasing from the builder(me). It will come with a new certificate of origin for the boat and title for the trailer. Engine PDI has not been done so you will get the full Mercury warranty. No expense was spared, this boat has the best of everything. 316 stainless used throughout on boat and trailer. 50hp Merc(2-stroke,with Vengeance stainless performance prop on the back). Very first production model from "Dirty Bird Custom Boats" (7 years in development )!!! I used this particular boat primarily for marketing purposes and has never seen the water(I've built several so I know it will rock and roll), but its time now to move it as I have other projects. The boat is show/water ready! Will consider interesting trades/partial trades(turn-key, no projects!) for car(late model German) or something performance like a Corvette,etc....I am in the market for a Delorean if you got one. Have over $35k into this package just in parts/materials. Waaaay too much to list, so please contact me if you have any questions. Also have a ton more pics as well. • Hand-made from the ground up • Hand-laid biaxial "COFAB" fiberglass (boat exceeds Coast Guard requirements) • Power tilt, power trim, and power trim tabs ( Volvo "QL" series ) • Custom stereo: AM / FM CD Sirus satellite radio, Rockford Fosgate AMP, JBL subwoofer, Boston Acoustic speakers • Custom gauges • Custom seats / upholstery • Sword in-lay in bow with custom L.E.D. lighting • Hand-built custom trailer: dual "flex axles", electric wireless brake system, inner fenders undercoated, L.E.D. lighting, matching wheels and tires , fold-away tongue • Boat and trailer both used 100% stainless hardware. ***NOTE***- this auction is for the boat and trailer only (not box trailer). I would be willing to sell 16ft(2ft v-nose) box trailer at additional cost with the boat(we can negotiate on that) as I was planning on selling it after the boat sold...thanks for looking!

1966 Donzi barrel back classic

1966 Donzi barrel back classic

$9,995

Portland, Oregon

Year -

Make -

Model -

Category -

Length -

Posted Over 1 Month

Private Seller (503) 810-1137 Photos Close Request Information * Name First Name * Email Telephone (optional) Best Time to Contact Anytime Morning Mid-day Evening Question/Comments (optional) Shop Safely: Protect Your Money. By using this site, you agree to our Terms of Use. Contact Seller 1966 Donzi barrel back classic,66 Donzi 18' is the 83rd Donzi built (hull #83) and is an ultra-rare triple hatch barrelback design, This is a Great boat ! 75+ MPH With this SBC LT-1 Corvette motor stroked to 383 done by Rex Hutchison Racing Engines with ONLY 43 hours, dyno shows 393 HP @5,500 RPM and 439 lbft of torque@ 3,600 RPM (dyno sheet avalible). Top quality parts. Stainless Marine exhaust with custom fabricated SS risers to match original exhaust tip locations. Also running a hydraulic trim Volvo 270 T upper coupled to a Volvo E-drive lower, hydraulic trim plates, newer aluminum fuel tank with 30+gallon capacity, full Sunbrella mooring cover, V&M single axle trailer also in very good condition. Never been in salt water, fresh water only and it shows. 503-810-1137 $9995, 5038101137 Finance this boat|Get an insurance quote|

1957 Chris Craft Barrel Back

1957 Chris Craft Barrel Back

$34,300

Chesnee, South Carolina

Year -

Make -

Model -

Category -

Length -

Posted Over 1 Month

Chris Craft was among the many boat builders who switched to wooden lapstrake construction for boats like this beautifully finished 1957 18 foot Barrel Back. Aged particularly well and is in great usable condition. Equipped with the desirable 5.7L Corvette V8. It features ventilating windshield panels. Mahogany bulkhead and mahogany seats. Including aft seating. Silver faced instruments. And much more. Always maintained meticulously on schedule with nothing but premium fluids parts and service every time. Full financing professional nationwide shipping and extended warranties are all available on approved credit