Tiller Handle Sailboat Boats for sale

22' 1978 Catalina 22 Sailboat

$6,995

Enid, Oklahoma

Year -

Make -

Model -

Category -

Length -

Posted Over 1 Month

For more details visit: http://www.BoatsFSBO.com/98079 BOAT OWNER'S NOTES for (1978 /CATALINA 22/SAILBOAT) - CALL BOAT OWNER(BLAINE RICHIE) @ 580-478-3330.OVERVIEW: THE CATALINA 22 IS AN EXTREMELY RELIABLE AND EASY TO HANDLE TRAILERABLE CRUISING SAILBOAT, WITH IT’S SWING KEEL IT IS EASY TO SAIL AND EASY TO TRAILER TO YOUR FAVORITE SAILING WATERS, YOU DON'T NEED AN EXPENSIVE MOORING, IT CAN BE STORED ON IT'S TRAILER AND PROTECTED WITH ITS CUSTOM (SAILOR’S TAILOR) COVER, LAUNCHED AT ANY RAMP, AND RIGGED IN JUST A FEW MINUTES.FEATURES: 1978 SINGLE AXLE STEEL TRAILER WITH SELF CONTAINED HYDRUALIC DRUM BRAKES INSTALLED IN 2013, 6 KNOTS PER HOUR UNDER POWER WITH A 8 HP MERCURY OUTBOARD PLUS A MOTOR MOUNT STAND TO HOLD THE OUTBOARD MOTOR WHEN IT IS NOT MOUNTED ON THE BOAT, LENGTH: 22' 0", TOTAL WEIGHT WITH TRAILER 3700 LBS, GREAT SAILING PERFORMANCE, 3 SAIL SETS THAT EACH INCLUDE A JIB AND MAIN SAIL. ONE SET IS A MYLAR RACING SAIL SET, MINIMIZE YOUR FUEL BILL - YOU CAN SAIL FOREVER FOR FREE, EASILY TRAILERED AND LAUNCHED, NO NEED FOR EXPENSIVE IN-THE-WATER STORAGE, LAUNCH AND RIG IN ABOUT AN HOUR, UNDER 8’ WIDE FOR LEGAL TRAILERING, FLOATS IN 30" OF WATER, FULL STANDING HEADROOM WITH THE TOP POPPED, 5 GALLON FRESH WATER SINK/SLIDING - REMOVEABLE GALLEY WITH ALCOHOL STOVE,.ENCLOSED HEAD, SLEEPS 4, (1 DOUBLE BERTH AND 2 SINGLES), ALL CURTAINS ARE INCLUDED, TILLER STEERING, TILLER HIKING STICK, TILLER AUTO PILOT.MISCELLANEOUS EQUIPMENT: 2 PROFESIONAL SAILING REFERENCE BOOKS, ALL SHEETS INCLUDED, ALL FIBERGLASS CONSTRUCTION WITH TEAK ACCENTS, PLENTY OF COCKPIT STORAGE, LOTS OF EXTRAS INCLUDED, BINOCULARS, FLARES, EXTRA ROPE, SWIMMING LADDER, LIFE RING, CABIN AND STORAGE COMPARTMENT LOCKS, TOP OF MAST WIND WEATHER VANE, FIRE EXTINQUISHER, AIR HORN, OARS, SPARE TIRE, 5 ADULT LIFE JACKETS, DISHES, USB AND 12 VOLT CONNECTIONS RUN OFF INCLUDED BATTERY, MULTIPLE DOCK BUMPERS, CLEANING SUPPLIES, DEPTH FINDER/AIRAND WATER THERMOMETER, VHF RADIO, 4 WINCHES AND WINCH HANDLES, FULL TOOL SET, 2 ANCHORS, MAIN SAIL COVER WITH BOAT NAME (WIND WALKER), CUSTOM CANVAS ENCLOSURE FOR POP TOP OPERATIONS, THE SWING KEEP PROVIDES LOW DRAFT (2’6”) WHEN RAISED AND MORE STABILITY AND SPEED WHEN LOWERED IN DEEPER WATERS (7 FEET). INSTRUCTIONS FOR RIGGING THE BOAT ARE INCLUDED AS WELL AS THE CATALINA OWNERS MANUAL.DESCRIPTION: THIS BOAT IS A MUST SEE AS IT IS IN EXCELLENT CONDITION AND HAS BEEN WELL TAKEN CARE OF, ON THE TRAILER AT HIGHWAY SPEED, YOU CAN VISIT GREAT PLACES THAT WATER BOUND BOATS WILL NEVER SEE, AND YOU CAN AVOID THE EXPENSE OF IN THE WATER STORAGE, THE CATALINA 22 OFFERS UNMATCHED SAILING PERFORMANCE, YOU CAN HAVE THE PEACE AND QUIET OF SAILING, ALONG WITH SWIMMING, FISHING, DIVING, OR JUST FOOLING AROUND ON THE WATER, YOU CAN LIVE ON THIS BOAT ON LAND OR ON THE WATER, LAUNCH THE BOAT, ANCHOR IN A QUIET COVE, AND YOU CAN BE AS FAR AWAY FROM THE WORLD AS YOU WANT TO BE, YOU CAN HAVE YOUR OWN ISLAND FOR FREE AT SOME OF THE MOST BEAUTIFUL VACATION AREAS ON EARTH, UNLIKE LAND BOUND RECREATION VEHICLES, YOU WILL NOT BE LIMITED TO CROWDED AND EXPENSIVE RV PARKS, YOU WILL NEVER TIRE OF THE WONDERFUL SENSATION OF SHUTTING OFF THE ENGINE AND ENJOYING THE QUIET SERENITY OF MOVING ALONG UNDER SAIL.THE PRICE IS LOW AT $6995, THE TRAILER IS YOUR MOORING AND THE WIND IS FREE.IF YOU HAVE ANY QUESTIONS ABOUT THIS BOAT CALL ME, (BLAINE RICHIE) @ 580-478-3330.

1977 Seafarer Futura 22' Project Sailboat

$1,200

Lake Worth, Florida

Year 1977

Make Seafarer

Model Futura

Category Cruiser Motorcycles

Length 22.0

Posted Over 1 Month

This boat is a Rhodes design and was made to be blue water capable (see the Seafarer Research Center website). It's a great project sailboat/trailer package for those with the spare time, skills and place to do the work or the money to pay others to do it for them. The boat needs bottom stripping/sanding and paint, as well as a tiller handle (just the wooden portion, not the bracket that is present). The trailer (1989 Shoreline) needs a jack stand top and a fender (see pics), but recently made it down here from Maryland. Sails (main and roller furling jib) are in very good shape. You are welcome to inspect her prior to bidding; please contact me here to arrange it. The photos are about a week old. I've only owned her a few weeks and upon delivery, realized she is more of a project than I have the time or place for. I'm cutting my losses and will not make a profit on this sale. She is for sale locally, so this listing may end early. Thanks for looking!

1977 Columbia Sailboat 29 New Bottom Paint Plus Many Extras

$5,000

Marina Del Rey, California

Year -

Make -

Model -

Category -

Length -

Posted Over 1 Month

Up for sale is this Columbia 29 Sailboat What You Get: - 29 Foot Boat with front jib sail and mainsail with new roller furling. - Craftsman powermate 1850 generator to run all electrical while at sea. - New iStart portable jumpbox battery charger. - new Garmin vhf300 radio. - New rear light pole install. - New sony waterproof stereo with surround sound and Bluetooth/iphone compadible - New Rutter tiller handle for steering. - Haul out Records by marina ship yard for new bottom paint, pressure wash and sandblasted. - New Acrylic dark tint entryway and all external wood replacement…Acrylic hatch cover for engine room. - Tinted all windows with 5% visibility - Installed 2 new batteries and 2 bilge pumps.

Hunter Sailboat 216 Excellent Condition Designed not to Capsize - 21'

$8,499

Gilbertsville, Kentucky

Year -

Make -

Model -

Category -

Length -

Posted Over 1 Month

The sailboat is located in Western Kentucky. The photo of a 2004 21' Hunter sailboat in the water is a dealer photo and may not accurately reflect the Hunter 216 we are selling. However, the remaining photos are actual photos of the sailboat. This fabulous 2004 Hunter 21’ sailboat has been thoroughly enjoyed and meticulously maintained. The Hunter fit our needs as a single person craft that worked as a keel boat that would not capsize. While a single person can easily handle this craft when day sailing, a crew of 4-6 will have tons of fun quickly skimming the water. This sailboat, motor and trailer were bought new from the factory in Saint Louis and have had one owner. There are less than 100 hours of water time. The mast is light and can be taken down by one person very easily in about 15 min. for trailering. Front support for the mast when down is on the trailer, and a rear support slides into a bracket on the stern of the boat. The boat has been garage kept and well maintained for continued and memorable hours of water fun. The price includes the sailboat, motor and trailer. Manufacturer Provided Description From the drawing board of noted sport boat designer, Glenn Henderson, the Hunter 216 is truly a fun boat to sail. Novices or seasoned skippers will appreciate the forgiving nature of the rig, the stability of the hull and simplicity of sailing it. The innovative underbody will provide exhilarating performance when pushed with the ability to power down whenever needed. The large cockpit will accommodate the crew with comfort and the cuddy can handle a portable head and a V-berth with storage. A special hydraulic lift mechanism allows for effortless lifting of the lead keel, and a unique lifting, VARA inboard rudder gives real performance with true beaching ability. Construction is by Hunter’s patented Advanced Composite Process, which combines thermoformed UV protected plastic, fiberglass mat and injected foam. The result is a tough, almost maintenance-free hull that is virtually unsinkable Specs – • Year – 2004• Length – 21’• Keel – Lifting• Hull Material – Composite Hull • Shape – Monohull• Engine – • Seating Capacity – 6 Dimensions – • Beam: 7 ft 11 in• LWL: 21 ft 6 in• Minimum Draft: 1 ft 0 in• Maximum Draft: 3 ft 6 in• Displacement: 1250 lbs• Dry Weight: 1250 lbs Sails – • Battened mainsail• Furling genoa Rigging – • Fractional Sloop Covers – • Lazy Bag• Lazyjacks Features –• Floats in only 12" with swing keel in up position• Draws only 3.51' with board down (and you can sail with her partially down)• Huge Cockpit• Can be sailed by one• Can carry 4 to 6• Includes small cuddy cabin big enough for a portapotty or head• Unique structure - - cut into pieces every piece will float due to foam core• Includes Motor mount and motor• Includes Mast support system• Includes Trailer Guide Bars• Includes Mainsail cover• Includes docklines, fenders• Includes Anchor and lines Equipment –• Anodized Fractional Rig w/Spreaders• 4:1 Boom Vang System• Hinged Mast• Halyards & Running Rigging• Mainsail/Jib• 4:1 Mainsheet System• Reefing System for Mainsail• ACP Structured Hull• Cast Lead Centerboard w/Hydraulic Lift System• Cuddy Cabin for Storage• Hatchboard and Lockable Hatch• Inboard VARA Rudder System• w/Easy Lift Rudder• Integral Centerline Toe Rail• Over 1,500 lbs. of Positive Flotation• Protective Rubrail• Stainless Steel Bow Eye• Stainless Steel Mooring Cleats (4)• Tiller ExtensionAdditional Equipment – • Trailer• Motor Shipping - The sailboat will not be shipped by the seller.

Laser Sailboat with Trailer / Ready to sail today / trailer has new tires

$1,500

Kansas City, Missouri

Year 1978

Make Laser

Model -

Category -

Length 14.0

Posted Over 1 Month

No longer race-ready, but still tons of fun. this much loved Laser, is ready for a new home. She's been cleaned up and is ready to sail as soon as you put her in the water. She comes with 2 piece mast and boom, Rudder with tiller extension, keel, one sail with battens, sail and spar bags, and a trailer that is road ready. This is the perfect boat for teaching your kids to sail. Easy for one person to launch and rig, even without a launch ramp. She's fast and snappy enough for even an experienced sailor to handle. Guaranteed that after a day sailing her, your face will hurt from smiling so much! Located in Kansas City, Mo 64116 Call Bill for info 816-916-9031

Very Rare 19 ft Southern-sail Skiffle sailboat motor and trailer turn key!

$6,000

Miami, Florida

Year 1982

Make Southernsail Skiffie

Model -

Category -

Length -

Posted Over 1 Month

FINAL REDUCTION BEFORE SHE'S OFF THE MARKET! FROM 7500 TO 6000!!Very Very Rare! only a hand full were made, Skiffie 1982 19 ft Southernsails Inc, (XUT) with a Johnson sailmaster 7.5 extra long shaft double- ender lapstrake heavy fiberglass sailboat in pristine conditions ( Faiths ) hull is shinny and smooth with great lines, main sail is great, working jib also, she was built by southernsails Inc in Clearwater Florida, has new varnished tiller handle with cover, Bimini top with boot cover, new Tung jack. tiller tamer new, wind indicator, lines, custom mast holder made out of aluminum, new chocks, anchor and rod new, cushions, recently rebuild entire tandem trailer with custom bunks ,new keel guides, supports, new axles, hubs, 4 new wheels and a new spare with carrier and cover, new Led trailer lights, safety chains, bow stopper, winch, strap, recently had bottom professionally painted, have Florida title and trailer registration on hand!, please serious inquiry's only. Many Thanks.LOA 19FIXED KEELBEAM 6"8DRAFT 2ftDISPLACEMENT 1900 lbs.SAIL AREA 143 sq.ftOUTBOARD MOTOR WELLSELF BAILING COCKPIT.

sailboat 33 ft Tarten Ten Race boat Day Sailor with incredible trailer

$18,000

Ada, Michigan

Year 1978

Make S&S

Model Tarten Ten

Category Daysailer Sailboats

Length -

Posted Over 1 Month

1978 S&S Tarten Ten in above average condition senior citizen owned. less that 100 actual hours of total actual use. comes with mast, jib, tiller handle and all deck railing is inside the boat. comes with a custom built trailer tri-axle 3 7k rated axles will hold up to 45 ft boat, has extender very heavy duty construction. add 16ft to ease launch. call 616 874 8235 for details paypal used for deposit only unless approved by seller. i do have a heavy duty cradle that is also on a trailer and ready for transport anywhere. the cradle is not offered with this action. may be purchased seperatly. the boat was appraised between 13 and 17 and the trailer was appraised at 10 to 12

21' CLARK SAN JUAN SAILBOAT- SLEEPS 4 + includes trailer (MAMARONECK, NY) 10543

$500

Mamaroneck, New York

Year 1976

Make CLARK

Model SAN JUAN

Category -

Length 21.0

Posted Over 1 Month

CAN EASILY BE VIEWED IN A BOAT YARD IN MAMRONECK, NEW YORK 10543. (if purchased, must be moved by the end of this month- with a few extra days if needed). The AMAZING Clark San Juan 21 is very easy to sail. Read all about it in the wikipedia link and do a Google/Bing/Yahoo search. Lots of info avail.Good first boat, a family boat, or a racing boat. The San Juan 21 continues to be a popular racer and enjoys many active racing fleets across the country.Beautiful and simple classic 1976 design.Rigging: Sloop, CutterBeam: 7 feetFixed-keelSteering: TillerHull: FiberglassSleeps four+ Clean titles for boat & trailer,. Boat is registered in New York until 2017+ Boat is in good/fair condition, normal wear, ready to sail. BUT needs a good cleaning. And if you want, the bottom could be painted. The wood hatch door could be replaced. Some dings on the keel. There are some small cracks in the roof that could be properly repaired. (very common in the San Juan). + Includes the original owners manual and everything in the photos (lots of extras)+ All standing and running rigging+ 4 sails: Large mainsail, Jib, a 110% working jib, a 135% genoa+ Sail Bags+ Good anchor+ Lots of PFD/life vests+ Reupholstered cabin cushions + Rudder+ Sail Cover+ FREE trailer GO TO YOUTUBE FOR VIDEOS of a San Juan 21 sailing: Google: San Juan Sailboats and Clark Boat Company - San Juan 21 ...GOOGLE: San Juan 21 Association Web SiteGOOGLE: San Juan 21 Fleet 1CHECK wikipedia photosCHECK WIKIPEDIA:The San Juan 21 blends a combination of performance and ease of sailing.[1] They are very easy to set up and can be put in the water in as little as 25 minutes. With the swing keel, they ride low on the trailer and can be launched and retrieved from any ramp. A handful of fixed-keel variants were produced, including a small number of shoal keel models. It is believed that fewer than 300 fixed-keel boats were produced, and even fewer of the shoal-keel boats (believed to be less than 20). Clark experimented with the fixed-keel design predominantly in the production plant located near Seattle, Washington.They handle much like big dinghies, yet with the 400-lb. keel, they are self-righting. This is not of much concern, as capsizing a San Juan 21 is not easy. Initially tender, the San Juan 21 heels to 15 degrees rather easily but firms up there, and once past 40 degrees, the helmsman has to make a rather big mistake to get it to go more. Once past 50 degrees or so, the sturdy little boat will round up and head into the wind.The San Juan 21 is a pleasure to sail for both novices and experienced racers. Due to its light weight (1400 lbs Class Weight), it accelerates briskly in puffs and will literally sail rings around most bigger boats in light to moderate winds. There are several one-design class fleets located at various lakes across the country with active racing schedules all summer. While designed more with performance in mind, the boat is comfortable for weekend cruising for two adults with two small children. It has space for a camping toilet and ample storage for other essentials.They are also easy to single-hand, with the fractional rig's small jib and large main.The sail inventory consists of a large mainsail, a small 110% working jib, a 135% genoa, and a spinnaker. Being a one-design class, rules limit the sails to be made from Dacron and the spinnaker from nylon. This keeps costs down.

AMF Alcort Sunfish,sailboat,daysailor,ready to sail,14ft,cart not included

$700

Riverhead, New York

Year 1975

Make AMF

Model -

Category Daysailer Sailboats

Length 13.9

Posted Over 1 Month

sunfish complete with excellent sail, boat, rudder, tiller, vintage hardware.beach dolly in pics not included, ready to sail. I broke off front handle today but broke in middle not were screws are, just replace handle if you want really doesn't need it.has a few blemishes as to be expected, payment within 2 days. will hold up to 2 weeks if paid in full within 2 days.when you hit the buy it now its to buy not to come and look at do that before buying or ask questions or send someone to check it out.

AMF Alcort Sunfish (complete boat)with custom beach dolly,sailboat,daysailor

$1,350

Riverhead, New York

Year 1985

Make AMF

Model -

Category Daysailer Sailboats

Length 13.9

Posted Over 1 Month

very nice 80's sunfish,dont know exact year put had to put a year in listing, complete with excellent sail, boat, rudder, tiller, custom made beach trailer or dolly, has over sized tires for beach sand. ready to sail. I broke off front handle today but broke in middle not were screws are, just replace handle if you want really doesn't need it.has a few blemishes as to be expected, payment within 2 days. will hold up to 2 weeks if paid in full within 2 days. will be away last weekend in may from Friday thru sunday, but available all week and next.

21' CLARK SAN JUAN SAILBOAT + 8' dingy + 6 HP motor + trailer in MAMARONECK, NY

$998

Mamaroneck, New York

Year 1976

Make CLARK

Model SAN JUAN

Category -

Length 21.0

Posted Over 1 Month

CAN EASILY BE VIEWED IN MAMRONECK, NEW YORK 10543. (if purchased, must be moved by the end of this month). You get EVERYTHING YOU NEED TO HIT THE WATER: 21' Sailboat AND an 8' Sandpiper dingy ($350 value) AND a like new 6 hp four-stroke Tohatsu (Mercury) long shaft outboard ($850 value), AND a Dry Dock trailer AND dingy motor: Tohatsu 2 1/4hp (needs minor repair). The AMAZING Clark San Juan 21 is very easy to sail. Read all about it in the wikipedia link and do a Google/Bing/Yahoo search. Lots of info avail.Good first boat, a family boat, or a racing boat. The San Juan 21 continues to be a popular racer and enjoys many active racing fleets across the country.Beautiful and simple classic 1976 design.Rigging: Sloop, CutterBeam: 7 feetFixed-keelSteering: TillerHull: FiberglassSleeps four+ Clean titles for boat & trailer,. Boat is registered in New York until 2017+ Boat is in good/fair condition, normal wear, ready to sail. BUT needs a good cleaning. And if you want, the bottom could be painted. The wood hatch door could be replaced. There are some small problem areas in the roof that could be properly repaired. (very common in the San Juan). BUT THE BOAT DOES NOT LEAK (top or bottom)+ Includes the original owners manual and everything in the photos (lots of extras)+ All standing and running rigging+ 4 sails: Large mainsail, Jib, a 110% working jib, a 135% genoa+ Sail Bags+ Good anchor+ Lots of PFD/life vests+ Reupholstered cabin cushions + Rudder+ Sail Cover+ FREE trailer ($500+ value)GO TO YOUTUBE FOR VIDEOS of a San Juan 21 sailing: Google: San Juan Sailboats and Clark Boat Company - San Juan 21 ...GOOGLE: San Juan 21 Association Web SiteGOOGLE: San Juan 21 Fleet 1CHECK wikipedia photosCHECK WIKIPEDIA:The San Juan 21 blends a combination of performance and ease of sailing.[1] They are very easy to set up and can be put in the water in as little as 25 minutes. With the swing keel, they ride low on the trailer and can be launched and retrieved from any ramp. A handful of fixed-keel variants were produced, including a small number of shoal keel models. It is believed that fewer than 300 fixed-keel boats were produced, and even fewer of the shoal-keel boats (believed to be less than 20). Clark experimented with the fixed-keel design predominantly in the production plant located near Seattle, Washington.They handle much like big dinghies, yet with the 400-lb. keel, they are self-righting. This is not of much concern, as capsizing a San Juan 21 is not easy. Initially tender, the San Juan 21 heels to 15 degrees rather easily but firms up there, and once past 40 degrees, the helmsman has to make a rather big mistake to get it to go more. Once past 50 degrees or so, the sturdy little boat will round up and head into the wind.The San Juan 21 is a pleasure to sail for both novices and experienced racers. Due to its light weight (1400 lbs Class Weight), it accelerates briskly in puffs and will literally sail rings around most bigger boats in light to moderate winds. There are several one-design class fleets located at various lakes across the country with active racing schedules all summer. While designed more with performance in mind, the boat is comfortable for weekend cruising for two adults with two small children. It has space for a camping toilet and ample storage for other essentials.They are also easy to single-hand, with the fractional rig's small jib and large main.The sail inventory consists of a large mainsail, a small 110% working jib, a 135% genoa, and a spinnaker. Being a one-design class, rules limit the sails to be made from Dacron and the spinnaker from nylon. This keeps costs down.

21' CLARK SAN JUAN SAILBOAT. Sleeps 4. FREE TRAILER. Larchmont NY

$2,500

New York, New York

Year 1976

Make CLARK

Model SAN JUAN

Category -

Length 21.0

Posted Over 1 Month

MUST BE PICKED UP IN LARCHMONT, NEW YORK 10538 You get EVERYTHING YOU NEED TO HIT THE WATER: 21' Sailboat AND an 8' Sandpiper dingy ($350 value) and like new 6 hp four-stroke Tohatsu (Mercury) long shaft outboard ($850 value) and dingy motor: Tohatsu 2 1/4hp (needs repair). The AMAZING Clark San Juan 21 is very easy to sail. Read all about it in the wikipedia link and do a Google/Bing/Yahoo search. Lots of info avail.Good first boat, a family boat, or a racing boat. The San Juan 21 continues to be a popular racer and enjoys many active racing fleets across the country.Beautiful and simple classic 1976 design.Rigging: Sloop, CutterBeam: 7 feetFixed-keelSteering: TillerHull: FiberglassSleeps four+ Clean titles for boat & trailer,. Boat is registered in New York until 2017+ Boat is in good/fair condition, normal wear, ready to sail. BUT needs a good cleaning. And if you want, the bottom could be painted. The wood hatch door could be replaced. There are some small problem areas in the roof that could be properly repaired. (very common in the San Juan). BUT THE BOAT DOES NOT LEAK (top or bottom)+ Includes the original owners manual and everything in the photos (lots of extras)+ All standing and running rigging+ 4 sails: Large mainsail, Jib, a 110% working jib, a 135% genoa+ Sail Bags+ Good anchor+ Lots of PFD/life vests+ Reupholstered cabin cushions + Rudder+ Sail Cover+ FREE trailer ($500+ value)GO TO YOUTUBE FOR VIDEOS of a San Juan 21 sailing: Google: San Juan Sailboats and Clark Boat Company - San Juan 21 ...GOOGLE: San Juan 21 Association Web SiteGOOGLE: San Juan 21 Fleet 1CHECK wikipedia photosCHECK WIKIPEDIA:The San Juan 21 blends a combination of performance and ease of sailing.[1] They are very easy to set up and can be put in the water in as little as 25 minutes. With the swing keel, they ride low on the trailer and can be launched and retrieved from any ramp. A handful of fixed-keel variants were produced, including a small number of shoal keel models. It is believed that fewer than 300 fixed-keel boats were produced, and even fewer of the shoal-keel boats (believed to be less than 20). Clark experimented with the fixed-keel design predominantly in the production plant located near Seattle, Washington.They handle much like big dinghies, yet with the 400-lb. keel, they are self-righting. This is not of much concern, as capsizing a San Juan 21 is not easy. Initially tender, the San Juan 21 heels to 15 degrees rather easily but firms up there, and once past 40 degrees, the helmsman has to make a rather big mistake to get it to go more. Once past 50 degrees or so, the sturdy little boat will round up and head into the wind.The San Juan 21 is a pleasure to sail for both novices and experienced racers. Due to its light weight (1400 lbs Class Weight), it accelerates briskly in puffs and will literally sail rings around most bigger boats in light to moderate winds. There are several one-design class fleets located at various lakes across the country with active racing schedules all summer. While designed more with performance in mind, the boat is comfortable for weekend cruising for two adults with two small children. It has space for a camping toilet and ample storage for other essentials.They are also easy to single-hand, with the fractional rig's small jib and large main.The sail inventory consists of a large mainsail, a small 110% working jib, a 135% genoa, and a spinnaker. Being a one-design class, rules limit the sails to be made from Dacron and the spinnaker from nylon. This keeps costs down.

2001 J46 sailboat sail boat J-46 sailing cruiser racing fresh water. UPGRADES!

$395,000

Charlevoix, Michigan

Year 2001

Make J Boats

Model J46

Category -

Length 46.0

Posted Over 1 Month

Beautiful, generously equipped and meticulously cared for freshwater J46 owned by senior couple. Used only for day sailing and minimal light cruising in northern Lake Michigan, Lake Huron and Lake Charlevoix for only 12 four month seasons (was not launched in 2012 and 2013). Always kept in inside heated storage when not in the water for the four month summer season. It is in pristine condition. J/46 may be the only investment grade sailing yacht of its size not requiring professional crew to sail at designed performance levels…..or to maintain. Two people can easily manage her upwind and down to achieve the same 8 knot passage-making speeds under sail that is possible when motoring with 76hp diesel auxiliary. The joy of sailing the perfect boat is, after all, a goal we believe every owner ultimately seeks. To insure that good sailing days are spent sailing rather than scrubbing and varnishing, J/46 is designed to be virtually maintenance-free. Her exquisite joinerwork is protected from the sun……below decks where it’s beauty can be preserved More photos available in this link: https://docs.google.com/document/d/1QEllizB6x4FKTe3kGwlbjYaLgJMrQEg8x6PdVtIa14Y/pub Factory Options: Refrigeration Package: -Seafrost Mechanical Refrigeration.-Additional Plates & controls for Freezer.-Supplementary 110VAC Shore power Assist. Supplementary Power Package: -Additional 210 amp Lifeline AGM Battery for total of 630 amps for house banks (location is in lieu of nav station bottom drawer).-Heart Freedom 25 Inverter/Charger (in lieu of std ProMariner 30-3 charger).-Heart Echo Charger (to service engine start battery through AC system).-Heart Link 2000 Battery Monitor (for (2) house battery banks).-Heart Link 10 Battery Monitor (for engine battery). Supplementary Plumbing Package: -Vacuflush Forward Head.-Dockside Water Inlet.-Seagull Water Purifier in Galley. Cruising Accessory Package: -Cockpit table.-Companionway Screens Additional Single Options: -ESPAR Diesel cabin heater.-Lewmar 64 CEST Power Primary Winches.-Bolstered Ultra Suede Cushions.-Radar Mast thru deck.-Microwave in galley.-Harken adjustable Genoa car leads.-Rubrail over cove stripe-28” High Pulpits & Stanchions in lieu of std height.-Sea water wash down pump w/faucet in anchor locker.-Hall Spars Windex.-Hall Spars “NO STRIKE’ lightning dissipater.-Hall Spars GAM antenna & cable.-Hall Spars painted carbon fiber whisker pole.-Hall Spar Whisker Pole Track and Car.-Hall Spars 3rd folding mast step.-Hall spars Dutchman mast sheave.-Hall spars Dutchman Halyard.-Flag Halyard & Hardware.- S. S. Turnbuckle Covers (6).-Cockpit Full Glass and Screen Enclosure.-Dodger to Bimini Insert.-Helm Pedestal Cover.-S. S. Grab Rail along aft edge of Dodger.-S. S. Grab Rails port & starboard on Dodger sides.-S. S. Dodger & Bimini supports in lieu of straps.-S. S. Bimini handrails port & starboard.-Power engine oil pump-out system.-Max Prop 3 Blade Feathering Propeller.-Dripless shaft seal.-Memory foam mattress in forward cabin in lieu of std.-Second custom V birth insert for additional standing room.-19” HD flat panel TV and small DVR.-2nd bottom refrigerator door.-Alpine stereo AM/FM w/6 disc CD player & Bose Marine cockpit speakers.-Weems & Plath Brass Ships Clock.-Weems & Plath Brass Barometer.-Variable Speed Cabin fans fore and aft cabins and main salon.-Prime bottom plus VC-TAR plus 2 coats VC-17 anti-fouling paint.-Awlgrip Hull Flag Blue w/Red Boot Stripes.-Patriot American Flag Graphics. Sail Package (Quantum): -Kevlar/Mylar/Dacron Tri Radial Cut full Batten Main & 135% Genoa.-MC6000 105% Cruising Jib.-Antal Mast Cars.-Dutchman Flaking System.-Asymetrical Spinnaker w/deployment bag.-Antal spinnaker Snuffer.-Harken Mark II Roller Furling System. B & G Hydra 2000 Navigator Pack: -Navigator Pack, Hydra 2000, Type 2.-Standard Full Function Display Pack, Hydra 2000.-20/20 Display Pack, Hydra, Green Backlight.-20/20 Display Pack, Hydra, Red Backlight.-Depth Sensor with Bronze Flush Mount Hull Housing.-Speed Sensor with Bronze flush Mount Hull Housing.-Analog display Pack, Apparent Wind Angle, 360 degrees w/cable.-Linear Rudder Position Sensor Pack, w/installation kit for Type 2 Ram.-Pilot Ram Drive Pack, Type 2 w/cables (12Vdc, adjustable rose joint).-Cable, 213 Mast w/bkt, 80ft.-Pin, Quick Release, Pilot.-Edson J46 Tiller Arm. Raytheon Radar/Chart Plotter and Accessories: -Upper Station – 7”Color LCD Pathfinder Radar w/Raychart and 24” 4kw Raydome.-WAAS GPS Antenna.-Cmap NT Northern Michigan.-Cmap NT Lake Huron and North Channel.-Radar Cable Connector (Radar Mast Base).-Edson 3-1/2” Deluxe Mast 144”.-Edson Adapter.-Edson Radar Platform, Deluxe.-Edson Long Antenna Bracket-Starboard and Port.-Edson 28” Antenna Hoop.-Edson 13” Antenna Extension (GPS antenna mount).-Shakespear TV Antenna 2030-G. Communications Options: -ICOM M502 VHF w/ Optional Cockpit HM-127 Remote-12 Volt Pedestal Outlet-Telephone and TV cable cockpit to nav station Safety Equipment: 2 Sospenders inflatable PFD w/harness, lanyard & rearm kit1 Crewfit inflatable PFD w/harness lanyard & rearm kit2 Regular PFD w/harness & lanyard4 Regular PFD6 Throwable floatation cushions2 Jack Lines 45 ft port & starboardI Radar reflector1 Bosun chair1 Throwable Life Sling1 deployable auto inflatable Life Saver Buoy4 Fire extinguishers – various types1 Submersible Hand Held HX460S VHF Marine Transceiver w/ barometer sensor1 Throwable Rescue Line Bag1 Avon 48lb Inflatable dinghy w/ Poly pro towing line, bridle & elect pump – fits in aft cockpit locker1 Honda 2hp 4 cycle dinghy motor & aft pulpit motor mount1 Winslow 6 person Super-Light Offshore Life Raft w/ SEP packed Survival Supplies Inflatable insulated double floor Heavy duty TriPod Arch tubes w/canopySpare parts: water pump impeller, 2 Racor fuel filtersVarious sizes of tapered wood emergency thru hull plugs 1 Handheld compass1 backup Yeoman digitized chart plotter with hand-held Magellan GPSVarious rescue flares as required by Coast GuardLakes Michigan, Huron and North Channel Charts Ground Tackle: 1 44lb Spade anchor w/swivel shackle, 25ft high test 3/8” chain and 250ft 5/8” rode1 Fortress Fx-37 Alum. Anchor w/ 15ft 5/16” chain & 200ft 5/8” rode in deployable anchor bag 250ft 5/8” Line for on-shore anchoring Dock Lines & Bumpers: 3 Taylormade bumpers w/blue covers6 Yale Red Colorline braided 5/8”x40ft dock lines w/Perma Buoy chafe guards Shore Power: 1 50ft 50 amp power cable1 60ft 30 amp power cable1 Adapter 50 amp to 30 amp Maintenance equipment: 1 Universal Pole w/boat hook, 2 brush heads & curve end1 50ft water hose Note: All 4 house batteries and the engine starting battery replaced May 2015 with Lifeline AGM (house) and Optimus (engine) batteries. J/46 Specifications Hull & Deck SCRIMpTM infusion molded sandwich construction using triaxial, biaxial and unidirectional glass reinforcements with Lloyd's and ABS approved end-grained balsa core. (SCRIMpTM is the patented resin infusion molding process of TPI Technologies, Inc.)TPI transferable ten yearwarranty against hull blisters. Interplastic vinylester resin on the outer hull layer.Lead & antimony fixed 9,350 lb., 6.2' draft, and fin/bulb keel bolted to a deep molded stub.White (other light colors are optional) Gel Coat hull with double tapered bootstripe and molded indented cove stripe. White gelcoat deck with choice of five non-skid colors in tones of white, gray and beige.HUIl-to-deck joint bond,ed with 3M 5200 and Plexus MASSO on the transom, side decks are covered with a thru-bolted clear anodized aluminum toe-rail.Two lazarette lockers on fantail, port cockpit seat locker and port utility locker for helmsperson outboard of wheel. Propane locker outboard of wheel to starboard drained and vented overboard with two 10lb aluminum bottles. Molded instrument pods on port and starboard coamings and on wheel pedestal.Molded companionway seahood with integral instrument pod.(3) Oorade boxes molded integrally into deck for ventilating owner cabin, main cabin and forward head area.Molded swim platform with off-center gate and fold-up ladder.Gasketed bow anchor locker and spinnaker storage area with overboard drain.316 stainless handrails on cabin trunk (4) total.GRP molded main structural bulkhead, glassed fore & aft on hull and deck as support for shroud chainplates with single door opening to v-berth cabin.Heavy duty molded structural keel support grid including engine bed, mast step, and longitudinal stiffeners. Fabricated aluminum mast step and engine bed tapping plates molded into structural keel grid.Positive traction nonskid on horizontal deck surfaces. Propulsion & Steering Yanmar 4JH-TE turbq-charged 76 hp, 4 cylinder, diesel engine with fresh water-cooling, dual R~cor fuel filters and 150 amp alternator.Yanmar C-type recessed engine instrument panel in cockpit with Acrylic cover including gauges for tachometer, fuel level, operating hour meter, fresh water temperature, amperage, oil pressure and oil temperature. Morse-type control gear shift and throttle mounted on pedestal.Parallel fuel system with 60 gallons in primary tank below the aft starboard berth, and 30 gallons in secondary tank behind aft bulkhead to starboard. Secondary tank gravity feeds into primary for 90 gallon total capacity.Two blade 20" Max Prop with 1..25" Aquamet shaft.AquaOrive self-aligning thrust bearing to minimize shaft vibration.Ultra Sound Acoustics VO-1 00 insulation in engine compartment.Balanced spade rudder constructed with unidirectional glass and large diameter shaft mounted in Harken composite rudder bearing to exceed ABS requirements.Aluminum emergency tiller.Edson 60" diamond series aluminum wheel with leather grip.Custom molded pedestal with guard and integral binnacle, 5" Ritchie compass, 9" x 12" instrurnent mounting area & Edson thru-shaft wheel brake.(2) Teak helm-station foot braces. Interior Satin varnished cherry bulkheads and furniture panels with cold molded cherry trim, drawer and cabinet faces. Main bulkhead with single opening and recessed cherry paneled door with Mobella lock-sets. Forward and aft heads trimmed in teak.Cherry trimmed vinyl headliner throughout forward, main and aft cabins. Polyurethane teak & holly veneer floor panels with underside and end-grain sealed with epoxy.Choice of interior cushion fabric colors. (ultra-suede or ultra-leather options available)5" layered & bolstered main settee split wrap-around cushions with two-tier split backrests. 4" foam cushions in fwd and aft cabins. Large twin berth forward cabin featuring 4 drawers, 4 lockers, hinge-up bunk tops to maximize storage; hinged V-berth filler; changing seat, hanging locker w/louvered door, and bureau/vanity with 2 drawers. locker. and cabinet above with cherry louvered doors & shelf.Forward head includes vanity with mirrored acrylic slider storage, teak towel rack, mirror storage cabinet below molded sink, enclosed by cherry paneled door (on outer face) and white laminate finish on head side.Stall shower with teak slat bench seat, cabinet locker with mid-height shelf outboard, shower fixture mounted on bulkhead with adjustable shower faucet. Local self-priming pump services shower sump and drains overboard.Pilot berth in main cabin to port with small mid-height convenience shelf at aft end.Two storage cabinets with 'Iouvered doors to ~ccommodate main cabin entertainment center above starboard settee. (2) Book storage shelves between cabinets with removable cherry retainer battens.One large drawer and one locker outboard of starboard settee backrest cushions.Settee backrests of cherry veneer and cherry trim.Varnished cherry wood hull slats in main, aft and V-berth cabins.Cherry main cabin drop-leaf table with removable fiddles, two drawers and internal bottle storage.Large 30 x36 sit-down. forward-facing navigation station with hinged tabletop. Features include; outboard shelf, access to chart storage and sliding organizer tray below table top, cushioned seat of layered bolstered foam. instrument cabinet with (2) large wood panel faces hinged at the bottom for quick access, file storage drawer below nav seat to fit hanging files, binocular & misc. storage cabinet outboard of seat, and series of three utility drawers on inboard tabie support face.Starboard aft cabin with recessed cherry paneled door, hanging locker with louvered door and bureau/vanity with 2 large drawers. hinged footlocker, and cabinet with cherry louvered door & shelf. Additional drawer above engine.Aft head/shower combination accessed via cherry paneled door. wet hanging area outboard. cabinet below molded sink, mirror, (2) teak grab rails and direct access door to lazarette locker area equipped with fore and aft divider. Teak companionway steps cold molded with angled ends & Treadmaster non-skid for safe entrance and exit. Cherry overhead grab rails in main cabin.All drawers and cabinets with polished positive-latch push buttons. Galley "Wheat Matrix" Fountainhead color for counter tops with cold-molded varnished & tapered cherry fiddles.Scandvik polished 8" deep SS double sink recessed below Fountainhead on forward island with deluxe hot/cold pressure-water gooseneck faucet and manual fresh water faucet with whale foot pump. Storage areas in louvered doors below sink for cleaning supplies and garbage pail with flip lid access.6.5 cu.!!. Deluxe icebox located on center island. Features include molded GRP box insulated with Glacier Bay Ultra R vacuum insulation panels and foam top. Organizing shelves & interior light included.3.5 cu.!!. ice box, convertible to optional freezer, located outboard of sink. Featuring molded GRP box with 3-1/2" foam insulation and mounting space for refrigeration cold plates.Three-burner Force 10 propane stove/broiler/oven with thermostat control, patented slide-away oven door recess and S.S. stove bar. Additional storage foot locker below oven.Plate, bowl, cup, and glass storage compartment on bulkhead att of stove.Top access dry good storage compartment below counter top directly outboard of sink.(3) Large cabinets mounted outboard and covered by three louvered cherry doors. Aft two cabinets installed with mid-height shelves. (Optional Microwave replaces middle cabinet door and area).Dual slider cabinet, bin storag8. and AC outlet mounted below cabinets. Flatware drawer, utensil drawer and utility cabinet with mid-height shelf and louvered door under outboard counter. Sink-top cutting-board.Stainless grab post on forward inboard galley corner. Plumbing Hot & cold pressure water system with 12-gallon hot water tank and accumulator tank. Service to (2) heads, forwa~d shower, galley, & swim platform shower.Self-priming direct sump pumps for showers draining into seacocks.Automatic bilge pump with float switch and dedicated panel in nav station wired direct to DC system. 120 gallons total water capacity in (2) custom molded tanks complete with baffles, inspection ports, and secured in place below main cabin settee berths.Raritan PH-2 heads with holding tanks. Overboard "Y"- valve offshore discharge and holding tank pump out systems. Two manually operated bilge pumps, one mounted in the cockpit and another in aft head with hose to reach bilge. (ORC category 2). Electrical Standard system batteries include: (1) group 40 (210 amp) and (2) group 31 (105amp) deep cycle batteries to serve the house, and (1) Optima 1000 (1,100 CCA) battery for dedicated service to the engine. All batteries are Concorde's Lifeline AGM sealed, absorbed glass mat type series.ProMariner ProMatic 30-3 Battery Charger. Balmar 91-150 Alternator and Max Charge external regulator with temperature sensor for altemator.BattJMaxx Automatic Battery System with remote momentary parallel switch near cockpit engine panel. .Master battery switch at n~l.Vstation with 1,2,Both,Off for House batteries and single On/Off switch for engine start battery.Deluxe Bass AC/DC backlit electrical panel w/digital condition meters, circuit breakers, accommodation for optional generator installation and air conditioning systems. Panel accommodates 33 DC breakers (24 occupied w/two spare standard) and 11 AC breakers (9 standard).Navigation, steaming/foredeck, anchor and tri-color masthead lights.50 amp 11OVAC shorepower system with 6 outlets, 50ft shore power cord and Guest galvanic isolator.Bonding system to meet ABYC project E-1.Propane solenoid switch panel in galley.Ten swiveling Imtra stainless halogen reading lamps, halogen overhead lights in main cabin, flexible armed lamp at navigation station, two florescent lights, one in each head.Four Hella variable speed cabin fans over berths. Deck Hardware (2) Lewmar 64CCST self-tailing 2-speed all chrome primary winches with gear ratio of 3.1: 1 in 1 gear and power ratio of 64:1 in 2nd gear located in recessed bases on cockpit coamings. "'(2) Lewmar 54CCST self-tailing 2-speed all-chrome halyard/reef/spinnaker secondary winches on cabin trunk.(2) Lewmar 48CCST self-tailing 2-speed all-chrome mainsheet winches outboard of traveler in recessed bases. (3) Lock-in Harken Speed-Grip 10" winch handles, (2) 8" Speed-Grip handles for mainsheet. Four cockpit mounted PVC winch handle holdersThurston cockpit dodger with roll-up forward window, removable side curtains, stanchion supports and stainless grab bar on aft edge.Thurston deluxe helmsman bimini with stanchion supports & viewing window (same color as dodger).Five white acrylic cockpit cushions for helmsman and cockpit seats.(2) Harken Black Magic 3010 (1OOmm) footblocks for genoa sheets when using dodger, mounted on cockpit coamings aft of primary winctTes. (2) Harken Black Magic 3006 (75mm) double footblocks with lock-off outboard of the primaries for spinnaker sheets and checkstays.(2) Harken Black Magic 3005 (75mm) mainsheet foot blocks wllockoffs mounted on angled pads at winches.2:1 Mainsheet system consisting of (2) Harken 1969 AirBlocks (75mm) mounted on traveler and (1) 3007 AirBlock (100mm) attached to boom bale. Harken 560-S Big Boat mainsheet traveler track with Harken 1939/1935 car w/control blocks for 6:1 purchase led to both sides of cockpit to 1893 track control ends through cockpit side mounted 222 blocks to 150 cam cleats. (2) 168 swivel blocks to adjust traveler from forward or aft side of track.Single rope clutchmounted in cockpit for heads ail furling. Lewmar Concept 2 anchor windlass system with #203 ropelchain gypsy, manual override, 1S0 amp breaker in nav station, hand held control unit mounted in forward deck anchor locker. Gypsy requires 3/8" ACCO G40 or G80 chain and S/8" braided rope.Custom 316 stainless mast collar with 10 bales for halyard and reef lines and forward halyard bar. (9) Schaefer 08-0S stainless halyard and reef blocks wlinvestment cast shackles.(4) Lewmar Superlock double rope clutches, mounted in pairs forward of each secondary winch.(2) Harken 1969 (7Smm) AirBlocks shackled to U-bolts at transom corners for mainsail checkstays.(2) Harken 1969 (75mm) AirBlocks shackled to U-bolts aft on toerail for spinnaker sheets.(2) Clear anodized aluminum "T" tracks (13' x 1.25") for jib/genoa leads. Additional 3' x 1.2S" track mounted outboard of1 00% jib position for outboard lead.(2) Schaefer 32-33UC screw-pin type jib/genoa lead blocks.(2) Schaefer OS-99 snatch blocks for spinnaker twingslor outboard jib/genoa leads.(2) Stainless t-track slider cars.Asymmetric.spinnaker deck gear including: (2) Harken 1969 (75mffi1 Airblocks mounted on "U" bolts near sternpulpit and (1) 1969 75mm AirBlock mounted on anchor roller.White molded flagstaff mounted in 316 SS deck socket on aft deck edge close to centerline with 4 x 6 American flag. aRC Bow pulpit of 316 SS with double rail offshore navigation lights and forward gate.aRC Stern rails of 316 SS w/2 rail split design including a stern boarding gate to starboard and stern light. Tapered 316 SS lifeline stanchions with SS bases mounted to toe rail.Double lifelines heights to meet ORC standards with boarding gates to P&S using Gibb hooks.Padded Sunbrella lifeline covers for each lifeline outboard of helmsman's station w/color to match dodger & bimini. Two 10" bow cleats, two 8" stern cleats, two 8" amidships cleats.Custom designed 316 SS bow roller/stem~ead to accommodate Simpson-Lawrence Delta 35,45 & COR 35,45 and Bruce 45 anchors. (Optional removable anchor roller to port)Seven Lewmar Ocean series articulated, bronze tinted ac,ylic hatches: size 70 on foredeck, size 60 in main cabin, (4) size 12 over forward cabin, aft cabin, shower, and head and (1) size 10 in aft head.White framed Bomar opening ports w/screen~ in cabin trunk and in cockpit walls for aft quarter cabin and head. Acrylic companionway hatch and two-part acrylic offshore drop-boards with inside/outside opening, lockable hasp. Four 12x20 and two 12x24 poly mesh line bags, one foredeck double line-bag. .(4) Vetus 4" dorade cowl ventilators to service forward cabin and head and main cabin. Removable stainless guards for forward dorades.316 SS swim ladder with gray PVC treads mounted on swim platform. SS step with PVC tread mounted on transom. Spars & Rigging Hall Spars carbon fiber mast of pre-preg carbon fiber autoclaved at 80 PSI at 250 deg F. Mast includes double airfoil carbon spreaders, carbon gooseneck, Awlgrip off-white finish, painted black bands, wire runs in conduit, Hall/Antal mainsailJrack with loader and end fittings to accommodate sail maker provided Antal mainsail sliders and/or boltrope. Also included with the mast are; Spartite mast wedge material, offshore tricolor/anchor light, bow and deck light with SS guard andJlag halyard cheek block at masthead and cleat at deck. Hall Spars boom of 6061-T6 aluminum with off-white Awlgrip finish, welded gooseneck fitting, lug for OuikVang internal 12:1 mainsail outhaul with external cleat, bale for mainsheet block and painted black bands. Outboard end to accommodate single line reef to starboard and 2nd clew reef to port. .Hall "J" length carbon fiber whisker pole with 2 bridles and trip line, short track on front of masJ, and two deck mounted retaining clips shipped loose for owner to locate.Navtec continuous rod rigging and N690 style open body turnbuckles with headstay -17 pre-assembled for furling system, backstay -17, uppers -17, intermediates -12, lowers -22.Harken MKIII Unit 2 size furling system with airfoil performance extrusion, corrosion proof spool and drum, tapered torque tube, AirSwivel for reduced weight aloft, cast aluminum Hardcote anodized chafe guard, and all black low stretch New England adjuster line.Hall Rigging package includes; two Technora jib halyards .and one Spectra spinnaker halyard each with Tylaska T-12 SS shackles and flemish eye terminations['2:'1 ',riain halyard of Technora with Wichard #1495 shackl~, XLS Mainsheet and two traveler control adjuster'lines, two XLS-900 Spectra genoa sheets, two Maxibraid taperedSpectra spinnaker sheets, one XLS Dacron spinnaker tack line, single 3/8" Crystalyne checkstays that can beclipped forward when not in use, burgee halyard of white 5/32" Dacron cord. Three reef lines are also included; Tack reef & clew reef #1, together, are one continuous reef line to starboard. Tack reef #2 doubles as cunningham to port. Clew reef #2 is included with it's own dedicated hardware. 2:1 Whisker pole foreguy with Schaefer 504-09 block with snap shackle.Sailtech -17 Long integral hydraulic backstay adjuster. Hall D-30 aluminum Ouik-Vang w/ Harken 30:1 cascading adjuster tackle & powerful stainless return spring to lift boom in light air and support boom with sail furled, eliminating the need for a topping lift.Custom designed 316 SS chainplates, stemhead and backstay tang. Installed Package Options Refrigeration PackageSeafrost Mechanical Refrigeration.Additional Plates & Controls for Freezer Supplementary 11OVAC Shorepower Assist. Supplementary Power PackageAdditional 210 amp Lifeline AGM Battery for total of 630 amps for house banks (location is in lieu of bottom nav station drawer).Heart Freedom 25 Inverter/Charger (in lieu of standard ProMariner 30-3 charger).Heart Echo Charger (to service engine start battery through AC system).Heart Link 2000 Battery Monitor (for (2) house battery banks).Heart Link 10 Battery Monitor (for engine battery). Supplementary Plumbing Package Vacuflush Forward Head. Dockside Water Inlet.Seagull Water Purifier in Galley. Cruising Accessory Package Cockpit Table.Companionway Screens.Espar D5LC heating system with ducting into the two sleeping cabins and main cabin.Lewmar 64CEST Two Speed Electric Primary Winches.UltraSuede or UltraLeather Covered Cushions in Main Cabin (in lieu of standard).Edson Radar Mast Thru-Deck and under-deck mounting platform (for 3.5" diameter mast). Microwave Oven in GalleySea Water Washdown in Anchor Locker.Harken Adjustable Genoa Leads.Many additional photos herehttps://docs.google.com/document/d/1QEllizB6x4FKTe3kGwlbjYaLgJMrQEg8x6PdVtIa14Y/pub Manufacturer Provided Description Great boats don’t happen overnight. Helped by new materials and techniques, they evolve from the joint experiences of designer, builder and owners to become state-of-the-art. J/46 is such a vessel, inheriting the proven hull shape of the J/44, an offshore blue water classic, having won the Fastnet, Sydney-Hobart, NYYC Queen’s Cup and Trans-Atlantic races. J/44 is the only Class of yacht ever to be given its own class start by the Cruising Club of America in the Newport-Bermuda Race. To create the J/46, a foot of sailing length is added for speed; a transom swim/boarding platform for convenience; a carbon fiber mast and low VCG 6.2’ shoal draft keel for more stability; and a resin-infused, composite hull and deck for greater strength. Below decks, the choice was clear, use the same beautifully varnished cherry or teak joiner work, entertainment center and styling so highly acclaimed in our deluxe J/160. J/46 is a maxi-Ditch yacht, the tallest yacht that can fit under the bridges of the Intra-Coastal WWaterway. Yet she is non-intimidating. A high length-to-beam ratio on the waterline of this sea-kindly yacht significantly improves tracking offshore in large waves and makes sail plan balance less critical. J/46 sails with either main or jib only, always responding predictably to a light touch on the helm. Sail power with good stability allows cruising with working jib rather than large genoa. That’s less work for the crew and improved visibility for the person on the helm. J Boats’ unique spinnaker system makes downwind sailing possible for two. A modern asymmetric spinnaker attaches to the top of the anchor roller, is contained within a cockpit-controlled snuffer, and is stored, ready-to-use, in the bow locker. The spinnaker is hoisted to the masthead, 2’ above the headstay intersect, leaving space for the snuffer to shift on a jibe. Jibing is then easy. One simply lets off one spinnaker sheet and pulls in the other.

1982 S2 8.5A 28 foot Sailboat with Inboard Yanmar Diesel - In Racine Wisconsin

$2,750

Racine, Wisconsin

Year 1982

Make S2

Model 8.5A

Category Cruiser Motorcycles

Length 28.0

Posted Over 1 Month

**** PLEASE NOTE: Because of the relatively low BUY IT NOW price, payment will be due within 24 hours via paypal. I will send you a paypal invoice after a successful "BUY IT NOW" or an accepted offer. Please only buy or offer if you have positive feedback. Your buy it now or offer constitutes a binding agreement to purchase so please ask questions BEFORE clicking "BUY IT NOW" or making an offer. After receiving your payment I will overnight you the title or meet you in person depending on timing and my availability.**** Very Nice S2 8.5A (28ft) for sale in Racine Wisconsin. I'm expecting a second child soon and really don't want to sell this excellent great lakes cruiser. Clean and clear Wisconsin title.Tiller steering. (always my preference)Inboard Yanmar diesel is extremely clean and fuel efficient. Recent full Yanmar service checkout since boat was last launched.Furling headsail in good shape. Newer mainsail in excellent shape.New Raymarine autopilot professionally installed. Shore power and long power cable. Halyards in good shape.New marine head and holding tank (never used). Chainplates recently professionally rebedded by boatyard. Interior in excellent shape.Solid fiberglass hull. All tabbed in joinery in excellent shape. Cored deck with NO soft spots. Very large cockpit.Includes steel cradle as well. I looked at everything in this size and price range in the lower half of lake Michigan for two years and this is the nicest boat I could find by leaps and bounds. Solid turnkey value. Launch is all ready paid for with the boat yard. You can be in the water tomorrow. No better deal can be found on solid and ready to sail Great Lakes cruiser with a clean inboard diesel - it is just time for me to move it along. Currently out of the water at Racine Riverside Marina in Racine, WI. Summer storage is paid through the end of this month and a launch is included in the purchase. If you chose not to launch until next season the storage rates at the Marina for winter are extremely reasonable and the pre-paid launch will still be yours come next summer. Here is a Review from "Practical Sailor" S2 8.5 MeterThe 8.5 is good for cruising the coasts in comfort and style--as long as you like the modern look.When Leon Slikkers founded S2 Yachts in 1973, much of the attention to detail that had previously characterized Slickcraft powerboats—Slikkers’ earlier boatbuilding venture— traveled with him to the new boatbuilding company. In the 13 years S2 sailboats were in production (S2 still makes powerboats), the company produced a variety of modern cruising designs from the board of Arthur Edmunds, all characterized by longish fin keels, freestanding spade rudders, straight sheerlines, and a staggering variety of draft options and cockpit locations. In the early ’80s, S2 reached more for the performance market with the Grand Slam series of small boats, and the 10.3 “offshore racer-cruiser.” These higher performance boats were designed by Scott Graham and Eric Schlageter, well known for their MORC and smaller IOR designs.The S2 8.5 is a 28-footer cast in the company’s traditional mold. Her hull dimensions, sail area, displacement, and general design characteristics put her square in the middle of the modern 28-footers such as the Tanzer 8.5, Newport 28, O’Day 28, and the Pearson 28.The boat’s styling is conventionally modern. She has a fairly straight sheer, fairly high freeboard, and low, raked cabin trunk with dark tinted flush ports. Production of the 8.5 ran from 1981 to 1983. The boat was replaced by the similar S2 8.6, which continued until S2 stopped making sailboats in 1986.ConstructionThe hull of the S2 8.5 is a solid hand layup. Glasswork is excellent, and is noted by owners as one of the main considerations in buying the boat. Gelcoat quality is excellent.Slight roving printthrough is evident, but it is not objectionable. Minor hard spots are visible in the topsides, probably caused by the attachment of interior furniture and bulkheads.The deck molding is cored with end grain balsa, giving a solid feel underfoot as well as providing reasonable insulating properties.S2’s hull-to-deck joint is the basic type that we would like to see adopted throughout the industry. The hull molding has an inward-turning flange, onto which the deck molding is dropped. The joint is bedded in flexible sealant, and through bolted on six inch intervals by bolts passing through the full length slotted aluminum toerail. The joint is also through bolted across the stem.All deck hardware is properly through bolted, although pulpits, cleats, and winches merely use nuts and washers on the underside of the deck, rather than the aluminum or stainless steel backing plates we prefer.Another feature of the hull-to-deck joint is a heavy, semi-rigid vinyl rubrail at the sheerline, quite aptly termed a “crash rubrail” by S2. This will go a long way toward absorbing the shock of the inevitable encounters with docks and the other hard objects that seem to be attracted to the topsides of the typical sailboat. Although this rail is black when the boat is new, it had dulled to a chalky gray on older S2’s we examined.The builder advertises “bronze seacocks on all through hull fittings.” These are not traditional tapered plug seacocks, but are ball valves mounted directly to through hull fittings. A proper seacock—whether it uses a ball valve or a tapered plug—has a heavy flange to allow through bolting to the hull. This is an important safety feature. Should a valve seize, it may become necessary to apply a great deal of leverage to the handle in order to open or close the valve. The deeply threaded through hull stem can easily break under these conditions, and more than one boat has been lost in this manner.We also suggest that seacocks be installed on the cockpit drain scuppers and the bilge pump outlet, both of which may be under water while the boat is sailing. Light air performance would benefit by the fairing in of the through hull fittings, particularly the head intake and discharge, both of which are far enough forward to have a significant effect on water flow past the hull.Ballast is a 3,000 pound lead casting, epoxied inside a hollow keel shell. We prefer an external lead casting bolted to the hull for its shock-absorbing qualities and ease of repair. This preference was reinforced recently when we examined an old Bristol 27 just sold by a friend. The surveyor noticed dampness near the bottom of the leading edge of the keel, which showed slight external damage. Probing the loose putty revealed some abrasion of the glass keel molding. In order to sell the boat, it was necessary to grind away a large portion of the glass at the front of the keel, dry out the ballast, and reglass the lead—a job that took several days of work and cost our friend a fair chunk of money.Much of the boat’s interior structure is plywood, glassed to the hull. Fillet bonding is neat and workmanlike with no rough edges to be found.Chainplates are conventional stainless steel flat bar, bolted to bulkheads and plywood gussets in the main cabin. These are properly backed with stainless steel pads. Due to the fact that the hull is lined throughout with a carpet-like synthetic material, it is not possible to examine the bonding of the chainplate knees to the hull. The stemhead fitting is a stainless steel weldment, through bolted to the deck and hull and reinforced inside the hull with a stainless steel gusset to prevent deflection of the deck from the pull aft of the headstay. We’d like to see a metal backup pad behind this fitting rather than the washers which are used.General construction is thoughtful and well executed, with excellent glasswork, a strong and simple hull-to-deck joint, and reasonably installed hardware and fittings.Handling Under PowerAlthough some early models of the 8.5 used a seven horsepower BMW diesel, the 1982 version employs an eight horsepower Yanmar. These small Yanmars are quite impressive, light in weight and far smoother than the company’s older rockcrushers.Because of the high freeboard and considerable windage of the 8.5, the standard engine is the absolute minimum power plant for the boat. Recognizing this fact, the company offered a 15 horsepower, two-cylinder Yanmar as an option. For another 75 pounds and $1,150, we would want this option on the boat if the ability to get places under power is a real consideration.The extra fuel consumption of the larger engine will scarcely be noticed. The 18 gallon aluminum fuel tank will probably give a range under power of over 250 miles—more than adequate for a 28 foot cruising boat.The fuel tank is located under the cockpit and is securely mounted and properly grounded. There is an easily reached fuel shut off between the engine and tank. Unfortunately, the fuel fill is located in the cockpit sole. Spilled diesel oil turns even the best fiberglass nonskid into an ice skating rink. Fuel fills should be located on deck, where spills can be efficiently washed away.Engine access is via a large removable panel on the inboard face of the quarterberth. This panel lacks any kind of handhold to make it easily removable, which will discourage regular checking of the engine oil. The top companionway step also removes for access, but it’s a long reach to the dipstick.There is no oil pan under the engine. It will be necessary to be very careful when changing oil to keep the bilge clean. We have yet to see anyone change oil and filters on a boat engine without spilling something.With the quarterberth panel removed, access for routine service is excellent. The quarterberth has remarkable headroom over, so that the mechanic will not feel like a trapped spelunker after a half hour of work. Engine removal will require some joinerwork disassembly.Handling Under SailThe S2 8.5 is no slug under sail. Her PHRF rating of 174 to 180 compares very favorably to other boats of her size and type. The Sabre 28, for example, has a rating of 198. The Pearson 28 about 195, and the O’Day 28 about 198.Part of this is no doubt due to the fact that the standard sails on the boat come from the North loft. While North’s OEM sails may not be the vertical cut Mylar-Kevlar wonders that adorn custom boats, they’re a lot better than most.S2 now uses Hall spars. The simple masthead rig is extremely clean, with airfoil spreaders and internal tangs. The boom features an internal outhaul and provision for two internally-led reefing lines, with cam cleats at the forward end of the boom.The deck-stepped mast is mounted in a stainless steel deck plate incorporating plenty of holes for the attachment of blocks. Halyards and Cunningham lead aft along the cabin house top to a pair of Lewmar #8 winches. Lewmar #16s are optional, but hardly necessary.The main is controlled by a six-part Harken rig mounted on the end of the boom, and a Kenyon traveler mounted on the aft cockpit coaming. This will work fine with the tiller-steered version of the boat. With wheel steering, the mainsheet is likely to be a nuisance to the helmsman.Because of the end-of-boom sheeting, a boom vang will be essential for full mainsail control. Ironically, the boat’s drawings show almost mid-boom sheeting, with the traveler mounted on the bridgedeck at the forward end of the cockpit. This is probably a better arrangement, although it heavily loads the center of the boom and requires more sheeting force.Owners of 8.5s have little but praise for the interior of the boat. The cabin has a wide feeling, created by pushing everything outboard. The “chart area” on the plan is a myth, as far as we can tell.Despite the fact that the shrouds are set well in from the rail, the boat lacks inboard headsail tracks. Rather, you are limited to snatch blocks shackled to the toerail track. A six-foot piece of track set inboard of the rail would be a useful addition.Standard headsail sheet winches are two-speed Lewmar #30s. Options include both larger winches and self-tailers, both of which are worth considering for either racing or cruising. The cockpit coamings are wide enough for mounting larger primaries and secondaries.The high-quality rig and sails add to the price of the S2, but they are additions well worth the cost.Deck LayoutThe deck layout of the 8.5 is clean and functional, with no toe stubbers to catch you unawares. There are two foredeck mooring cleats, but no bow chocks. The necessity to lead an anchor line well off the boat’s centerline, coupled with high freeboard forward, is likely to result in a boat which sails around on her anchor or mooring. The 8.5 has a pair of wide stainless steel chafing strips at the bow which will greatly protect the deck from the chafe of the anchor line.The 8.5’s foredeck anchor well is one of the best we’ve seen. It is shallow—just deep enough to hold an anchor and adequate rode. There are double scuppers, which offer less likelihood of clogging. The lid is held on by a full-length piano hinge, and there is a positive latch.The shallow locker well above the waterline means that water is less likely to enter through the scuppers, which can be a real problem with a deep anchor well. When the bow pitches into waves, a deep anchor well can fill with water, and if the scuppers clog with debris, you can find yourself sailing around with several hundred pounds of extra weight in the worst possible position. There is no provision for securing the bitter end of the anchor rode, but a big galvanized eyebolt installed in the well by the owner will solve that one.The running lights leave something to be desired. Their location at deck level just aft of the stem makes them vulnerable to damage when handling ground tackle. We much prefer an international style bicolor mounted on the pulpit, another two feet off the water: easier to see, and out of the way. Wiring for the running lights is exposed in the anchor well, and should be secured out of the way.A recessed teak handrail runs the full length of the cabin trunk, serving the dual function of heavy weather handhold and cabin trim piece. Its shape makes it far easier to oil or varnish than the conventional round handrail, although the wide, flat section seems somewhat awkward after years of grabbing round rails.The 8.5’s cockpit is the maximum size we’d want to see on a boat of this size. The T-shape is designed to accommodate the optional wheel steerer, yielding a somewhat odd layout for the tiller-steered version. A bench seat spans the aft end of the cockpit. Although this makes good seating in port, we doubt that you’d want anyone sitting there under sail: too much weight in the end of the boat. It does make a natural helmsman’s seat for wheel steering.The engine controls and instrument panel are also located at the aft end of the cockpit, and are basically inaccessible to the helmsman of a tiller-steered version.There are two lifting lids in the aft cockpit bench, giving access to a cavernous space under the cockpit. To be useful, dacron bags should be fitted to the inside of these lockers. Then, they’ll be handy stowage for spare sheets and blocks.There are comfortable contoured seats along each side of the cockpit, with a huge locker under the port seat. Although plywood pen boards somewhat separate this locker from the engine space under the cockpit, it would be far too easy for deeply piled junk to get knocked over the board and into the engine. This locker should be partitioned into smaller spaces unless it is to be used exclusively as a sail locker.The battery boxes, fitted at the forward end of the locker, could benefit from plywood or fiberglass lids to keep battery acid off gear which might find its way onto the batteries. The box is designed to take two batteries—one battery is standard—stored in plastic containers. A single lid covering the whole box would be more efficient.The huge cockpit will accommodate up to six for sailing, and eight for in-port partying. The cockpit seat bottoms are contoured, and the cockpit coamings slope outboard for more comfortable seating. However, the seats are both too narrow and too short for sleeping.The forward end of the cockpit is protected by a narrow bridgedeck. However, the cockpit coatings extend a full foot above the level of the bridgedeck, To block the companionway to the level of the top of the coamings will require leaving two of the three drop boards in place when sailing.Although there is moderate taper to the sides of the companionway, making it easier to remove the drop boards, it is still necessary to lift each board about five inches before it can be removed. This is far safer than many tapered companionways, where boards practically fall out if you look at them wrong. The companionway slide is one of the best we’ve seen. It’s a contoured piece of acrylic fitted with a convenient grabrail. It slides easily in extruded aluminum channels, and is fitted with a fiberglass storm hood. As on many boats, the aft cabin bulkhead slopes forward, rendering it impossible to leave the drop boards out for ventilation when it rains.BelowdecksOwners consistently praise the interior design and finishing of S2 sailboats. From looking at the 8.5, it’s pretty easy to see why.There are no exposed interior fiberglass surfaces except the head floor pan molding. The hull and cabin overhead are lined with a carpet-like synthetic fabric. While this will undoubtedly cut down on condensation, we at first wondered how this fabric would hold up over time. Inevitably, the hull liner and even the overhead will get wet. In freshwater areas, this is no problem. The water will eventually evaporate. In salt water, however, wet fabric never seems to dry. Salt draws moisture like a magnet draws steel. Since first seeing this boat, however, we’ve had good experiences with the fabric. Be sure, however, to get a good wet-or-dry vacuum to keep it clean.Interior layout is fairly conventional, with Vberths forward, and immediately aft, a full width head. The head can be closed off from both the forward cabin and the main cabin with solid doors—a real luxury in a boat this size. There is a large hanging locker in the head, and reasonable storage space for toilet articles.The word for the main cabin is “wide,” with the settees pushed as far outboard as they can go. Décor is a little heavy on the teak for our taste, but it is one of the better coordinated interiors we have seen. S2 had a good interior decorator.A fold-down dining table seats four. When folded against the bulkhead, it is held in place by a single latch, which makes us nervous.Neither settee is full length. The foot of the port settee runs under the galley counter, making it long enough for sleeping, although your feet may feel a little claustrophobic in the tiny footwell.The starboard settee is an unusual configuration. The aftermost 12" of the settee folds up to form an arm rest, leaving a gap between the end of the settee and the head of the quarterberth.Inexplicably, this gap is referred to on the accommodation plan as a “charting area,” although there is neither a standard nor an optional chart table. It’s sort of like the designer ran out of energy before completing the interior design.Over the non-existent “charting area” is the best electrical panel we’ve seen on a 28 foot boat. The panel has a locking battery switch, battery test meter, and a panel with room for 14 circuit breakers, although only half are installed on the standard boat.The space is welcome, since with the proliferation of marine electronics most electrical panels are woefully inadequate.Most quarterberths tend to induce claustrophobia. That of the 8.5 is more likely to exacerbate any tendencies you might have to agoraphobia. At last, a quarterberth which will not give you a concussion when you sit bolt upright in the middle of the night after your neighbor drags down on you in a wind shift.The standard main cabin sole is carpet-covered fiberglass. For an additional $325, teak and holly was available for the traditionalist. We’d want it. Unfortunately there is no access to the bilge in the main cabin. None. This is inexcusable, and could be dangerous. A few hours with a saber saw should solve this rather basic problem.The galley is workable and accessible, with no awkward posturing required to do the dishes. The sink gets an A+. It is a full nine inches deep, is large enough to take a frying pan, and mounted close to the centerline.In contrast, the icebox gets a C-. It is larger than normal on a boat of this size, but it drains to the bilge, has a poorly insulated top, and a tiny, uninsulated hatch without a trace of a gasket. Boo.Because of limited counter space, the two burner Kenyon alcohol stove is mounted athwartships, rather than fore and aft. This means that the stove cannot be gimballed, and that it is necessary to reach across the inboard burner to reach the outboard one. Given the fact that countertop gimballed stoves are usually dangerous, the lack of gimballing doesn’t bother us much. What does bother us is that if you want to upgrade the stove to something more functional, the limited space allocated will stretch your ingenuity.A fold down table at the end of the galley counter gives additional counter space, but it must be left up in order to use the port settee for sleeping.Roominess, excellent execution, and good color coordination are trademarks of the interiors of all S2s, and the 8.5 fits well into this enviable tradition.ConclusionsThe S2 8.5 is a good boat for cruising the Great Lakes or any coast in comfort and a certain amount of style. Her appearance may be a little modern for traditionalists, with her straight sheer and European-style cabin windows.Pricey? Yes, but when you look at the things that go into the boat—the rig, good sails, and a comfortable, well finished interior—the price may seem a bit less painful. You still pay for what you get.

1970s Alcort Sunfish Fiberglass Sailboat - Day Sailer - Novice to Expert Sailor

$750

Warrensburg, Missouri

Year 1975

Make Alcort

Model Sunfish

Category Daysailer Sailboats

Length 14.0

Posted Over 1 Month

Midwest Sunfish Sailboat, 1970s! This boat is in overall good shape and has always been kept indoors. The boat has not been cleaned and mild dirt on the sail was not washed prior to pictures. The boat has been in storage for several years and therefore the decision is to let her go to someone who will sail her again. She has been a good, reliable boat and never let us down. The boat has all its parts and accessories except for the centerboard, tiller and rudder... which have somehow been misplaced. The boat has had a mild fiberglass repair on the hull (see pictures) but it does not leak. The sail is in strong condition and also has a few repairs (see pictures). As you can see, rudder/tiller assemblies can be purchased online (new and used) as well as centerboards (new and used). The sail comes with its original bag. Available for local pickup. Shipping might be possible for a fee. Call Jason with any questions 6608646900 Features: The distinctive lateen sail gives the Sunfish an anachronistic appearance. Using a lateen rig for this style boat shifts the advantage toward better performance in lighter air and contributes to it having good down-wind characteristics. The hull’s very mild "V" bottom and hard chine make Sunfish a most stable boat for its size, along with enabling it to sail on a plane. Planing allows the boat to achieve a speed greater than theoretical hull speed based on length at waterline. Having a down-wind performance advantage helps the Sunfish to achieve a planing attitude at lower wind speeds. Designed as a water-tight, hollow-body pontoon, a hull like the Sunfish has is sometimes referred to as "self-rescuing" because the boat can be capsized and its cockpit swamped without threat of the boat sinking. Sunfish Boat Specifications LOA: 13\'9" Beam: 4\'1" Draft: 2\'11" Sail Area: 75 Square Feet Hull Weight: 120 Pounds Capacity: 1-2 people Skill Level: Beginner-Expert Race Level: Club International Optimal Weight: upto 190 pounds Transport: Car top carrier, hand dolly, over-the-road trailer The sailplan requires just 2 lines to control and the boat can be set up in less than 5 minutes. The patented kick-up rudder system allows full beach landings with no problems. The hard-chined hull and low sail plan provide unmatched stability and a forgiving feel. The Sunfish hull is light enough to throw on top of your car with ease. The Sunfish combines performance, stability and durability in a package that appeals to beginners and experts alike. If it's racing you crave, the International Sunfish Class has a full time staff that sanctions more than 1000 events each year. Add the hundreds of local and regional events to that list and you can stay pretty busy racing your Sunfish. The class will keep you posted with its quarterly magazine "Windward Leg" and provide valuable performance tips. The elegant simplicity, performance, and intelligent economy of the Sunfish is unmatched. The Sunfish enjoys fantastic resale value. Highlights: Convenient storage in the back of cockpit which is perfect for extra gear or a cooler Patented kick-up rudder makes beach launches, landings, and shallow-water sailing effortless. Self-bailing cockpit Hydrodynamic daggerboard maximizes upwind performance. Lateen rigged sail: 1.) automatically depowers when hit by a gust of wind 2.) two sides of the sail are supported which ensures durability 3.) easy to rig and derig Mainsheet is the only control line that you need to use to enjoy the simple pleasures of sailing a Sunfish. Simple main halyard is one of the two lines on the Sunfish, it hoists and lowers the sail in a matter of seconds, enabling spontaneous enjoyment of the water Stainless steel bow handle: facilitates carrying, docking, and holding the boat into the wind while launching or loading